Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
Specifications
Brake mechanisms of lobbies and back wheels - the general information
The parking brake - a design and the principle of functioning
Pressure valve limiter - a design and the principle of functioning
Antiretractable system - the device, the principle of functioning and a precautionary measure
System of anti-blocking of brakes (ABS) - the general information, the principle of functioning
System of dynamic stabilization (VDC) - the general information, the principle of functioning
Check of a state replacement of blocks of disk brake mechanisms of forward wheels
Removal, check of a state and installation of forward brake disks
Removal, service and installation of disk brake mechanisms of forward wheels
Check of a state and replacement of blocks of disk brake mechanisms of back wheels
Removal, check of a state and installation of back brake disks
Removal, service and installation of disk brake mechanisms of back wheels
Removal, service and installation of the main brake cylinder (MBC)
Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
Removal, installation and check of serviceability of functioning of the valve limiter of pressure
Replacement of brake fluid
Pumping of a hydraulic path of brake system
Check of a state and replacement of flexible brake hoses
Check of a state and replacement of tubes of a brake path
Removal, service, installation and adjustment of a pedal of a foot brake
Removal, check of a state, installation and adjustment of the sensor switch of stoplights
Removal, installation, check of a state and adjustment of the lever of the drive of the parking brake
Removal, check of a state and installation of elements of the hummock drive of the parking brake
Removal, installation and adjustment of the mechanism of the parking brake
Removal, installation, check of a state and adjustment of components of the antiretractable device
Removal, installation and check of serviceability of functioning of assembly of the module of the ABS management/hydromodulator
Check of sequence of operation of valves of the ABS hydromodulator
Removal, installation and check of serviceability of functioning of forward wheel ABS sensors
Removal, installation and check of serviceability of functioning of back wheel ABS sensors
Removal, installation and check of a condition of rotors of wheel sensors
Removal, installation and diagnostics of the sensor of overloads (G-sensor)
Problem diagnostics of ABS
Removal, installation and adjustment of the module of management of VDC
Removal, installation and check of serviceability of functioning of the VDC hydromodulator
Check of sequence of operation of valves of ABS and VDC hydromodulators
Removal, installation and check of serviceability of functioning of the sensor of withdrawal / cross overloads
Removal, installation and check of serviceability of functioning of the sensor of an angle of rotation of a steering wheel of VDC
Removal, installation and check of serviceability of functioning of wheel sensors with rotors
Removal, installation and check of serviceability of functioning of the switch of deactivation of VDC (VDC OFF)
Problem diagnostics of VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal, installation and check of serviceability of functioning of the sensor of an angle of rotation of a steering wheel of VDC
Details of installation of the sensor of an angle of rotation of a steering wheel of VDC
REMOVAL
|
|
| 1. Disconnect a negative wire from the battery.
2. Remove the module of a driver's frontal safety cushion (see the Head Onboard electric equipment).
|
|
3. Bring forward wheels of the car into rectilinear situation, give a fixing nut and remove a steering wheel from a shaft of a steering column, - use a stripper.
1 — the Stripper |
|
|
4. Turn out the screw of fastening of the lower cover of a casing of a steering column. |
|
|
5. Turn out two fastenings of the top cover of a casing of a column, release a clamp of a plait of an electrical wiring and disunite the socket of the sensor of an angle of rotation of a steering wheel.
1 — the Plait
2 — the Contact socket |
6. Turn out fixing screws and remove assembly of a contact drum with the sensor of an angle of rotation of a steering wheel.
|
|
INSTALLATION
|
|
|
1. Make sure that forward wheels are in rectilinear situation.
|
|
2. Put assembly of the sensor on a steering column. |
3. Center (see the Head Onboard electric equipment) and put a contact drum on the regular place.
4. Screw and tighten 7 screws of fastening of a contact drum / sensor of an angle of rotation of a steering wheel.
5. Put a steering wheel on the regular place, center it and fix a nut, having tightened the last with the demanded effort (44 Nanometers). In order to avoid damages track that the directing finger of a contact drum got to a reciprocal opening in stupichny part of a steering wheel, at once release contact sockets of an electrical wiring of a safety cushion, horn and tempostat, having passed them throughout the directing opening in a steering wheel.
6. Further installation is made as it should be, the return to an order of dismantle of components. Track that the gap between a landing surface of a steering wheel and face surfaces of covers did not exceed the limit of the admissible range (2 ÷ 4 mm).
7. Install into place the safety cushion module (see the Head Onboard electric equipment), then connect a negative wire to the battery.
8. In summary it is necessary to make installation of the central position of the sensor of an angle of rotation of a steering wheel and zeroing of the sensor of withdrawal / cross overloads (see the Section Removal, installation and adjustment of the module of management of VDC). |
|
Check of serviceability of functioning of the sensor
|
|
