Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
   Specifications
   Brake mechanisms of lobbies and back wheels - the general information
   The parking brake - a design and the principle of functioning
   Pressure valve limiter - a design and the principle of functioning
   Antiretractable system - the device, the principle of functioning and a precautionary measure
   System of anti-blocking of brakes (ABS) - the general information, the principle of functioning
   System of dynamic stabilization (VDC) - the general information, the principle of functioning
   Check of a state replacement of blocks of disk brake mechanisms of forward wheels
   Removal, check of a state and installation of forward brake disks
   Removal, service and installation of disk brake mechanisms of forward wheels
   Check of a state and replacement of blocks of disk brake mechanisms of back wheels
   Removal, check of a state and installation of back brake disks
   Removal, service and installation of disk brake mechanisms of back wheels
   Removal, service and installation of the main brake cylinder (MBC)
   Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
   Removal, installation and check of serviceability of functioning of the valve limiter of pressure
   Replacement of brake fluid
   Pumping of a hydraulic path of brake system
   Check of a state and replacement of flexible brake hoses
   Check of a state and replacement of tubes of a brake path
   Removal, service, installation and adjustment of a pedal of a foot brake
   Removal, check of a state, installation and adjustment of the sensor switch of stoplights
   Removal, installation, check of a state and adjustment of the lever of the drive of the parking brake
   Removal, check of a state and installation of elements of the hummock drive of the parking brake
   Removal, installation and adjustment of the mechanism of the parking brake
   Removal, installation, check of a state and adjustment of components of the antiretractable device
   Removal, installation and check of serviceability of functioning of assembly of the module of the ABS management/hydromodulator
   Check of sequence of operation of valves of the ABS hydromodulator
   Removal, installation and check of serviceability of functioning of forward wheel ABS sensors
   Removal, installation and check of serviceability of functioning of back wheel ABS sensors
   Removal, installation and check of a condition of rotors of wheel sensors
   Removal, installation and diagnostics of the sensor of overloads (G-sensor)
   Problem diagnostics of ABS
   Removal, installation and adjustment of the module of management of VDC
   Removal, installation and check of serviceability of functioning of the VDC hydromodulator
   Check of sequence of operation of valves of ABS and VDC hydromodulators
   Removal, installation and check of serviceability of functioning of the sensor of withdrawal / cross overloads
   Removal, installation and check of serviceability of functioning of the sensor of an angle of rotation of a steering wheel of VDC
   Removal, installation and check of serviceability of functioning of wheel sensors with rotors
   Removal, installation and check of serviceability of functioning of the switch of deactivation of VDC (VDC OFF)
   Problem diagnostics of VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




d9f1bda0

The parking brake - a design and the principle of functioning

Design of the mechanism of the parking brake

1 — the Brake board
2 — the Lock ring
3 — the Spring washer
4 — the Executive lever
5 — the Forward boot
6 — the Back boot
7 — Razzhimnaya a spring
8 — Razzhimnaya a level
9 — Directing boots

10 — the Returnable spring of a forward boot
11 — the Returnable spring of a back boot
12 — the Adjusting spring
13 — the Regulator
14 — the Plate of the directing spring
15 — the Directing spring
16 — the Anchor finger
17 — the Cap of a service opening of access to the regulator


Design of the hummock drive of the parking brake

1 — the Lever of the drive of the parking brake
2 — the Sensor switch of raising of the parking brake
3 — the Lock-nut
4 — the Adjusting nut
5 — the Equalizer
6 — the Arm
7 — the Collar
8 — the Left driving cable
9 — the Clamp (only for models with disk brake mechanisms of back wheels)

10 — the Right driving cable

Efforts of a tightening of threaded connections, Nanometer

T1: 5.9
T2: 18
T3: 32


Principle of functioning of the parking brake

1 — the Driving cable
2 — the Executive lever
3 — Razzhimnaya a level
4 — the Boot A

5 — the Boot B
6 — Returnable springs
7 — Anchor fingers
8 — the Point of support "Р"


Designs of the mechanism and the hummock drive of the parking brake are shown on illustrations.

When raising of the control lever located between forward seats, the executive lever of the back brake mechanism under the influence of the effort developed by a driving cable develops a razzhimny level concerning the point "Р" in the direction of "F". Being developed, the razzhimny level presses brake boots to a working surface of a drum. Boots have a floating design and keep on a brake board by means of anchor fingers, and the boot A is displaced under the influence of the effort developed by directly razzhimny level whereas the boot B nestles on a drum surface under the influence of force of reaction of "F" through the point of support "Р".

At an otpuskaniye of the parking brake the driving cable is weakened and boots come back to starting positions under the influence of the efforts developed by returnable springs.