Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
   Specifications
   Brake mechanisms of lobbies and back wheels - the general information
   The parking brake - a design and the principle of functioning
   Pressure valve limiter - a design and the principle of functioning
   Antiretractable system - the device, the principle of functioning and a precautionary measure
   System of anti-blocking of brakes (ABS) - the general information, the principle of functioning
   System of dynamic stabilization (VDC) - the general information, the principle of functioning
   Check of a state replacement of blocks of disk brake mechanisms of forward wheels
   Removal, check of a state and installation of forward brake disks
   Removal, service and installation of disk brake mechanisms of forward wheels
   Check of a state and replacement of blocks of disk brake mechanisms of back wheels
   Removal, check of a state and installation of back brake disks
   Removal, service and installation of disk brake mechanisms of back wheels
   Removal, service and installation of the main brake cylinder (MBC)
   Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
   Removal, installation and check of serviceability of functioning of the valve limiter of pressure
   Replacement of brake fluid
   Pumping of a hydraulic path of brake system
   Check of a state and replacement of flexible brake hoses
   Check of a state and replacement of tubes of a brake path
   Removal, service, installation and adjustment of a pedal of a foot brake
   Removal, check of a state, installation and adjustment of the sensor switch of stoplights
   Removal, installation, check of a state and adjustment of the lever of the drive of the parking brake
   Removal, check of a state and installation of elements of the hummock drive of the parking brake
   Removal, installation and adjustment of the mechanism of the parking brake
   Removal, installation, check of a state and adjustment of components of the antiretractable device
   Removal, installation and check of serviceability of functioning of assembly of the module of the ABS management/hydromodulator
   Check of sequence of operation of valves of the ABS hydromodulator
   Removal, installation and check of serviceability of functioning of forward wheel ABS sensors
   Removal, installation and check of serviceability of functioning of back wheel ABS sensors
   Removal, installation and check of a condition of rotors of wheel sensors
   Removal, installation and diagnostics of the sensor of overloads (G-sensor)
   Problem diagnostics of ABS
   Removal, installation and adjustment of the module of management of VDC
   Removal, installation and check of serviceability of functioning of the VDC hydromodulator
   Check of sequence of operation of valves of ABS and VDC hydromodulators
   Removal, installation and check of serviceability of functioning of the sensor of withdrawal / cross overloads
   Removal, installation and check of serviceability of functioning of the sensor of an angle of rotation of a steering wheel of VDC
   Removal, installation and check of serviceability of functioning of wheel sensors with rotors
   Removal, installation and check of serviceability of functioning of the switch of deactivation of VDC (VDC OFF)
   Problem diagnostics of VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment









d9f1bda0


Removal, installation and check of serviceability of functioning of back wheel ABS sensors

REMOVAL

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. The car also establish to Poddomkratta it on props.

3. Remove the filter of a fuel tank.

4. Disconnect an electrical wiring of the wheel sensor.

5. Release an intermediate clamp of fastening of a plait of an electrical wiring of the sensor on a body element.

6. Turn out bolts of fastening of basic arms of a plait.

7. Remove the ABS sensor from the suspension bracket lever, - do not pull the sensor for an electrical wiring plait, try not to damage a polar tip.

8. For check of a condition of a rotor of the sensor which is built in in hinged assembly remove a power shaft.

CHECK

 PERFORMANCE ORDER

 See also Section Problem Diagnostics of ABS.

The description of procedures of check and adjustment of wheel sensors is provided in the Section Removal, installation and check of serviceability of functioning of forward wheel ABS sensors with only that difference that the nominal size of a working gap (S) makes for back sensors 0.44 ÷ 0.94 of mm. Adjustment is made by selection of laying No. 26755AA000.

INSTALLATION

 PERFORMANCE ORDER

Installation is made as it should be, the return to an order of dismantle of components. Track correctness of laying and reliability of fixing of a plait of an electrical wiring (the left sensor - yellow isolation, right - white). All fixture should be tightened with the demanded effort (see Specifications and accompanying illustrations to the subsection "Removal"). Do not forget to adjust working gaps by selection of laying No. 26755AA000.