Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
   Specifications
   Brake mechanisms of lobbies and back wheels - the general information
   The parking brake - a design and the principle of functioning
   Pressure valve limiter - a design and the principle of functioning
   Antiretractable system - the device, the principle of functioning and a precautionary measure
   System of anti-blocking of brakes (ABS) - the general information, the principle of functioning
   System of dynamic stabilization (VDC) - the general information, the principle of functioning
   Check of a state replacement of blocks of disk brake mechanisms of forward wheels
   Removal, check of a state and installation of forward brake disks
   Removal, service and installation of disk brake mechanisms of forward wheels
   Check of a state and replacement of blocks of disk brake mechanisms of back wheels
   Removal, check of a state and installation of back brake disks
   Removal, service and installation of disk brake mechanisms of back wheels
   Removal, service and installation of the main brake cylinder (MBC)
   Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
   Removal, installation and check of serviceability of functioning of the valve limiter of pressure
   Replacement of brake fluid
   Pumping of a hydraulic path of brake system
   Check of a state and replacement of flexible brake hoses
   Check of a state and replacement of tubes of a brake path
   Removal, service, installation and adjustment of a pedal of a foot brake
   Removal, check of a state, installation and adjustment of the sensor switch of stoplights
   Removal, installation, check of a state and adjustment of the lever of the drive of the parking brake
   Removal, check of a state and installation of elements of the hummock drive of the parking brake
   Removal, installation and adjustment of the mechanism of the parking brake
   Removal, installation, check of a state and adjustment of components of the antiretractable device
   Removal, installation and check of serviceability of functioning of assembly of the module of the ABS management/hydromodulator
   Check of sequence of operation of valves of the ABS hydromodulator
   Removal, installation and check of serviceability of functioning of forward wheel ABS sensors
   Removal, installation and check of serviceability of functioning of back wheel ABS sensors
   Removal, installation and check of a condition of rotors of wheel sensors
   Removal, installation and diagnostics of the sensor of overloads (G-sensor)
   Problem diagnostics of ABS
   Removal, installation and adjustment of the module of management of VDC
   Removal, installation and check of serviceability of functioning of the VDC hydromodulator
   Check of sequence of operation of valves of ABS and VDC hydromodulators
   Removal, installation and check of serviceability of functioning of the sensor of withdrawal / cross overloads
   Removal, installation and check of serviceability of functioning of the sensor of an angle of rotation of a steering wheel of VDC
   Removal, installation and check of serviceability of functioning of wheel sensors with rotors
   Removal, installation and check of serviceability of functioning of the switch of deactivation of VDC (VDC OFF)
   Problem diagnostics of VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment









d9f1bda0


Removal, service and installation of disk brake mechanisms of back wheels

REMOVAL

 PERFORMANCE ORDER

The order of performance of procedure is similar described in the corresponding subsection of the Section Removal, check of a state and installation of forward brake disks.

DISMANTLING

 PERFORMANCE ORDER

1. Having hooked a screw-driver, remove a ring of fixing of a boot of the piston.

2. Remove a boot.

3. Slowly giving compressed air to the union of connection of a flexible brake hose, push out the piston from the cylinder, - before an end face of the piston establish wooden whetstone about 30 mm thick.

4. Having hooked a screw-driver, take a piston cuff from the support cylinder.

5. Remove a protective cover and the plug of a lock bolt (finger) from the support case.
6. Remove a protective cover of the directing bolt (finger).
7. Attentively study a condition of the removed components. Check the case of a support and the piston for existence of signs of uneven wear, mechanical damages and traces of development of corrosion. Make sure of lack of signs of aging of material of a boot, cuff and protective covers. Replace defective components within the let-out remnabor.

ASSEMBLY

 PERFORMANCE ORDER

Act according to the instructions provided in the corresponding subsection of the Section Removal, service and installation of disk brake mechanisms of forward wheels.

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. The order of installation of brake shoes is described in the Section Check of a State and Replacement of Blocks of Disk Brake Mechanisms of Back Wheels. The effort of a tightening of bolts of fastening of an anchor bracket makes 78 Nanometers. Bolts of fastening of the case of a support are tightened with effort of 39 Nanometers, a nipple bolt - with effort of 18 Nanometers.

 Copper sealing washers of the nipple socket of a flexible brake hose are subject to replacement without fail! Track that the hose at connection was not overwound!