Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
Specifications
Brake mechanisms of lobbies and back wheels - the general information
The parking brake - a design and the principle of functioning
Pressure valve limiter - a design and the principle of functioning
Antiretractable system - the device, the principle of functioning and a precautionary measure
System of anti-blocking of brakes (ABS) - the general information, the principle of functioning
System of dynamic stabilization (VDC) - the general information, the principle of functioning
Check of a state replacement of blocks of disk brake mechanisms of forward wheels
Removal, check of a state and installation of forward brake disks
Removal, service and installation of disk brake mechanisms of forward wheels
Check of a state and replacement of blocks of disk brake mechanisms of back wheels
Removal, check of a state and installation of back brake disks
Removal, service and installation of disk brake mechanisms of back wheels
Removal, service and installation of the main brake cylinder (MBC)
Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
Removal, installation and check of serviceability of functioning of the valve limiter of pressure
Replacement of brake fluid
Pumping of a hydraulic path of brake system
Check of a state and replacement of flexible brake hoses
Check of a state and replacement of tubes of a brake path
Removal, service, installation and adjustment of a pedal of a foot brake
Removal, check of a state, installation and adjustment of the sensor switch of stoplights
Removal, installation, check of a state and adjustment of the lever of the drive of the parking brake
Removal, check of a state and installation of elements of the hummock drive of the parking brake
Removal, installation and adjustment of the mechanism of the parking brake
Removal, installation, check of a state and adjustment of components of the antiretractable device
Removal, installation and check of serviceability of functioning of assembly of the module of the ABS management/hydromodulator
Check of sequence of operation of valves of the ABS hydromodulator
Removal, installation and check of serviceability of functioning of forward wheel ABS sensors
Removal, installation and check of serviceability of functioning of back wheel ABS sensors
Removal, installation and check of a condition of rotors of wheel sensors
Removal, installation and diagnostics of the sensor of overloads (G-sensor)
Problem diagnostics of ABS
Removal, installation and adjustment of the module of management of VDC
Removal, installation and check of serviceability of functioning of the VDC hydromodulator
Check of sequence of operation of valves of ABS and VDC hydromodulators
Removal, installation and check of serviceability of functioning of the sensor of withdrawal / cross overloads
Removal, installation and check of serviceability of functioning of the sensor of an angle of rotation of a steering wheel of VDC
Removal, installation and check of serviceability of functioning of wheel sensors with rotors
Removal, installation and check of serviceability of functioning of the switch of deactivation of VDC (VDC OFF)
Problem diagnostics of VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal, installation, check of a state and adjustment of the lever of the drive of the parking brake
REMOVAL
|
|
|
1. The car also establish to Poddomkratta it on props.
2. Remove back wheels.
3. Remove the central console (see the Head Kuzov).
4. Release an adjusting nut of a driving cable of the parking brake in the basis of lever assembly.
|
|
5. Give fixture and remove assembly of the lever of raising of the parking brake. |
|
|
6. Unbend a lock uvula on the lever and disconnect a driving cable.
1 — the Lever
2 — the Driving cable |
|
|
INSTALLATION
|
|
|
Installation is made upside-down. The fixture of the lever is tightened with effort of 18 Nanometers, an adjusting nut - with effort of 5.9 Nanometers. Track that the driving cable is passed in the directing tunnel. In summary make adjustment of the lever (see below). |
|
Check and adjustment
|
|
|
1. Count number of clicks of a ratchet when raising the lever with effort about 20 kgfs (196 N). If the number of clicks does not conform to standard requirements (7 ÷ 8), make necessary adjustment (see further).
|
|
2. Uncover the central console. 3-5 times with effort cock the lever of the parking brake. Rotation of the regulator achieve the demanded number of clicks when raising the lever with effort of 20 kgfs, then tighten a lock-nut with the demanded effort (5.9 Nanometers). In case of need make adjustment brake mechanisms of back wheels (see the Section Removal, installation and adjustment of the mechanism of the parking brake).
1 — the Lever
2 — the Lock-nut
3 — the Adjusting nut |
3. Establish into place a cover of the central console. |
|
|
|
