Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
   Specifications
   Brake mechanisms of lobbies and back wheels - the general information
   The parking brake - a design and the principle of functioning
   Pressure valve limiter - a design and the principle of functioning
   Antiretractable system - the device, the principle of functioning and a precautionary measure
   System of anti-blocking of brakes (ABS) - the general information, the principle of functioning
   System of dynamic stabilization (VDC) - the general information, the principle of functioning
   Check of a state replacement of blocks of disk brake mechanisms of forward wheels
   Removal, check of a state and installation of forward brake disks
   Removal, service and installation of disk brake mechanisms of forward wheels
   Check of a state and replacement of blocks of disk brake mechanisms of back wheels
   Removal, check of a state and installation of back brake disks
   Removal, service and installation of disk brake mechanisms of back wheels
   Removal, service and installation of the main brake cylinder (MBC)
   Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
   Removal, installation and check of serviceability of functioning of the valve limiter of pressure
   Replacement of brake fluid
   Pumping of a hydraulic path of brake system
   Check of a state and replacement of flexible brake hoses
   Check of a state and replacement of tubes of a brake path
   Removal, service, installation and adjustment of a pedal of a foot brake
   Removal, check of a state, installation and adjustment of the sensor switch of stoplights
   Removal, installation, check of a state and adjustment of the lever of the drive of the parking brake
   Removal, check of a state and installation of elements of the hummock drive of the parking brake
   Removal, installation and adjustment of the mechanism of the parking brake
   Removal, installation, check of a state and adjustment of components of the antiretractable device
   Removal, installation and check of serviceability of functioning of assembly of the module of the ABS management/hydromodulator
   Check of sequence of operation of valves of the ABS hydromodulator
   Removal, installation and check of serviceability of functioning of forward wheel ABS sensors
   Removal, installation and check of serviceability of functioning of back wheel ABS sensors
   Removal, installation and check of a condition of rotors of wheel sensors
   Removal, installation and diagnostics of the sensor of overloads (G-sensor)
   Problem diagnostics of ABS
   Removal, installation and adjustment of the module of management of VDC
   Removal, installation and check of serviceability of functioning of the VDC hydromodulator
   Check of sequence of operation of valves of ABS and VDC hydromodulators
   Removal, installation and check of serviceability of functioning of the sensor of withdrawal / cross overloads
   Removal, installation and check of serviceability of functioning of the sensor of an angle of rotation of a steering wheel of VDC
   Removal, installation and check of serviceability of functioning of wheel sensors with rotors
   Removal, installation and check of serviceability of functioning of the switch of deactivation of VDC (VDC OFF)
   Problem diagnostics of VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment









d9f1bda0


Removal, installation and adjustment of the mechanism of the parking brake

REMOVAL

 PERFORMANCE ORDER

1. Remove a brake disk (see the Section Removal, check of a state and installation of back brake disks).
2. Remove returnable springs of boots of the parking brake.

3. By means of a screw-driver with a flat sting remove the directing spring and an anchor finger of a forward boot of the parking brake.

4. Remove a razzhimny level with the spring.
5. Remove the directing spring and an anchor finger of a back boot of the parking brake.
6. Take off brake boots.

7. Disconnect a driving cable from the executive lever of the parking brake.

8. Having hooked a screw-driver, remove a lock ring and separate the executive lever from a boot, - try not to lose a spring washer.
9. Check a condition of a contact surface of a drum of a brake disk. In case of identification of deep furrows, zadir and other damages replace a disk.
10. Measure the internal diameter of a drum. Compare result of measurement to standard requirements (Nominal rate: 170 mm; limit admissible value: In 171 mm), in case of need replace a disk.
11. Measure the residual thickness of frictional overlays of brake boots. Compare results of measurements to standard requirements (Nominal rate: 3.2 mm; limit admissible value: 1.5 oo), in case of need replace boots in a set for both brake mechanisms.

ADJUSTMENT

 PERFORMANCE ORDER

1. Remove a rubber cap of a service opening from the back party of a brake board, pass a suitable screw-driver throughout an opening and, rotating it the adjusting screw, achieve pressing of boots to a contact surface of a drum, then release the adjusting screw on 3-4 teeth back.
2. Having finished adjustment, establish into place a cap.
3. Check correctness of adjustment of the lever of raising of the parking brake, in case of need make the corresponding adjustment (see the Section Removal, installation, check of a state and adjustment of the lever of the drive of the parking brake).