Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
Specifications
Brake mechanisms of lobbies and back wheels - the general information
The parking brake - a design and the principle of functioning
Pressure valve limiter - a design and the principle of functioning
Antiretractable system - the device, the principle of functioning and a precautionary measure
System of anti-blocking of brakes (ABS) - the general information, the principle of functioning
System of dynamic stabilization (VDC) - the general information, the principle of functioning
Check of a state replacement of blocks of disk brake mechanisms of forward wheels
Removal, check of a state and installation of forward brake disks
Removal, service and installation of disk brake mechanisms of forward wheels
Check of a state and replacement of blocks of disk brake mechanisms of back wheels
Removal, check of a state and installation of back brake disks
Removal, service and installation of disk brake mechanisms of back wheels
Removal, service and installation of the main brake cylinder (MBC)
Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
Removal, installation and check of serviceability of functioning of the valve limiter of pressure
Replacement of brake fluid
Pumping of a hydraulic path of brake system
Check of a state and replacement of flexible brake hoses
Check of a state and replacement of tubes of a brake path
Removal, service, installation and adjustment of a pedal of a foot brake
Removal, check of a state, installation and adjustment of the sensor switch of stoplights
Removal, installation, check of a state and adjustment of the lever of the drive of the parking brake
Removal, check of a state and installation of elements of the hummock drive of the parking brake
Removal, installation and adjustment of the mechanism of the parking brake
Removal, installation, check of a state and adjustment of components of the antiretractable device
Removal, installation and check of serviceability of functioning of assembly of the module of the ABS management/hydromodulator
Check of sequence of operation of valves of the ABS hydromodulator
Removal, installation and check of serviceability of functioning of forward wheel ABS sensors
Removal, installation and check of serviceability of functioning of back wheel ABS sensors
Removal, installation and check of a condition of rotors of wheel sensors
Removal, installation and diagnostics of the sensor of overloads (G-sensor)
Problem diagnostics of ABS
Removal, installation and adjustment of the module of management of VDC
Removal, installation and check of serviceability of functioning of the VDC hydromodulator
Check of sequence of operation of valves of ABS and VDC hydromodulators
Removal, installation and check of serviceability of functioning of the sensor of withdrawal / cross overloads
Removal, installation and check of serviceability of functioning of the sensor of an angle of rotation of a steering wheel of VDC
Removal, installation and check of serviceability of functioning of wheel sensors with rotors
Removal, installation and check of serviceability of functioning of the switch of deactivation of VDC (VDC OFF)
Problem diagnostics of VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
|
Removal, check of a state and installation of back brake disks
Otpuskaniye of boots of the parking brake
The "stuck" disk can be removed from stupichny assembly by a vvorachivaniye and a gradual tightening of couple of bolts of M8 in openings In
|
|
1. Release wheel nuts, a back of the car and establish to a poddomkratta it on props, remove the corresponding wheel.
|
|
2. Turn out two fixing bolts, remove a brake support and, without disconnecting from it a flexible hydraulic hose, tie up to suspension bracket elements, - track that the hose did not stretch. |
3. Cock and release the parking brake.
4. Rotating the adjusting screw passed through a service opening in a brake board (previously take a rubber cap) a screw-driver with a flat sting, take away brake boots of the parking brake from a working surface of a drum, then remove assembly of a brake disk.
5. The "stuck" disk is removed from stupichny assembly by means of couple of bolts of M8 rolled in special openings in stupichny part of a disk. |
|
Check of a state
INSTALLATION
|
|
