Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
- Brake system
   Specifications
   Brake mechanisms of lobbies and back wheels - the general information
   The parking brake - a design and the principle of functioning
   Pressure valve limiter - a design and the principle of functioning
   Antiretractable system - the device, the principle of functioning and a precautionary measure
   System of anti-blocking of brakes (ABS) - the general information, the principle of functioning
   System of dynamic stabilization (VDC) - the general information, the principle of functioning
   Check of a state replacement of blocks of disk brake mechanisms of forward wheels
   Removal, check of a state and installation of forward brake disks
   Removal, service and installation of disk brake mechanisms of forward wheels
   Check of a state and replacement of blocks of disk brake mechanisms of back wheels
   Removal, check of a state and installation of back brake disks
   Removal, service and installation of disk brake mechanisms of back wheels
   Removal, service and installation of the main brake cylinder (MBC)
   Removal, installation and check of serviceability of functioning of the vacuum amplifier of brakes
   Removal, installation and check of serviceability of functioning of the valve limiter of pressure
   Replacement of brake fluid
   Pumping of a hydraulic path of brake system
   Check of a state and replacement of flexible brake hoses
   Check of a state and replacement of tubes of a brake path
   Removal, service, installation and adjustment of a pedal of a foot brake
   Removal, check of a state, installation and adjustment of the sensor switch of stoplights
   Removal, installation, check of a state and adjustment of the lever of the drive of the parking brake
   Removal, check of a state and installation of elements of the hummock drive of the parking brake
   Removal, installation and adjustment of the mechanism of the parking brake
   Removal, installation, check of a state and adjustment of components of the antiretractable device
   Removal, installation and check of serviceability of functioning of assembly of the module of the ABS management/hydromodulator
   Check of sequence of operation of valves of the ABS hydromodulator
   Removal, installation and check of serviceability of functioning of forward wheel ABS sensors
   Removal, installation and check of serviceability of functioning of back wheel ABS sensors
   Removal, installation and check of a condition of rotors of wheel sensors
   Removal, installation and diagnostics of the sensor of overloads (G-sensor)
   Problem diagnostics of ABS
   Removal, installation and adjustment of the module of management of VDC
   Removal, installation and check of serviceability of functioning of the VDC hydromodulator
   Check of sequence of operation of valves of ABS and VDC hydromodulators
   Removal, installation and check of serviceability of functioning of the sensor of withdrawal / cross overloads
   Removal, installation and check of serviceability of functioning of the sensor of an angle of rotation of a steering wheel of VDC
   Removal, installation and check of serviceability of functioning of wheel sensors with rotors
   Removal, installation and check of serviceability of functioning of the switch of deactivation of VDC (VDC OFF)
   Problem diagnostics of VDC
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




d9f1bda0

Check of sequence of operation of valves of ABS and VDC hydromodulators

 See also Section Problem Diagnostics of VDC.


ABS hydromodulator

Check is carried out as it should be similar described in the Section Check of Sequence of Operation of Valves of the ABS Hydromodulator, - the diagnostic card is given in an illustration.

 When using SSM functioning begins with a point And.
HIGH = High level of tension; LOW = Low level of tension; ON = Vkl; OFF = Vykl

 


VDC hydromodulator

Check without application of SSM

 PERFORMANCE ORDER

1. Connect diagnostic plugs to plugs No. No. 5 and 8 of the heater of a driver's seat of the diagnostic socket, close to the block.
2. Include transfer and achieve rotation of wheels of the car with a frequency, 2.75 km/h are lower than the corresponding speed of the movement, then switch off ignition.
3. Start the engine, make sure of serviceability of operation of control lamps of ABS and VDC and within 0.5 seconds after their shutdown, squeeze out a pedal of a foot brake at first once, then still twice within 3 more seconds, - at the end the pedal should be released.

 Do not squeeze out a pedal of coupling!

4. After completion of check switch off ignition.

 

Check with application of SSM

 PERFORMANCE ORDER

 If performance of check with application of SSM is not possible owing to any violation.


 At the diagnostic plugs connected to the diagnostic socket (see an illustration 28.1) performance of check is not possible!

1. Connect SSM to the car DLC socket located at the left under the dashboard.
2. Include ignition, then include food of SSM.
3. Transfer SSM to the mode of check of brake system {BRAKE CONTROL}.
4. Activation of check of sequence of operation of ABS happens at a choice of subsection of the menu {Function check sequence}.
5. At emergence on the message display screen "Firmly squeeze out a pedal of a foot brake" (Press Brake Pedal Firmly), it is necessary to squeeze out a pedal with effort of 100 kgfs (when performing check at the stand)/35 kgfs (when checking with use of measuring instruments (see the Section Removal, installation and check of serviceability of functioning of assembly of the module of the ABS management/hydromodulator).

 Do not squeeze out a pedal of coupling! Emergence of the message of "Press YES" means that it is necessary to press the YES button. The course of check will be reflected in the monitor screen.

Exit from the check mode

 PERFORMANCE ORDER

The exit with transition of VDC to the mode of normal functioning comes from the check mode in the following cases:

g) At increase in frequency of rotation of any of wheels up to the size, the corresponding speed of the movement more than 10 km/h;
h) At a detachment of diagnostic plugs from plugs No. No. 5 and 8 of the diagnostic socket (without application of SSM);
i) At an otpuskaniye of a pedal of a foot brake / disconnection of the sensor switch of stoplights;
j) At lateness of squeezing of a pedal of a foot brake after inclusion of ignition and shutdown of control lamps of ABS and VDC (without application of SSM);
k) At delay of squeezing of a pedal of a foot brake more than for 0.5 seconds after shutdown of a control lamp of ABS (without application of SSM);
l) Upon completion of a test cycle.