Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
- Routine maintenance
   Schedule of routine maintenance of Subaru Legacy and Outback cars
   Specifications
   General information about settings and adjustments
   Check of levels of liquids (according to the Schedule of routine maintenance)
   Replacement of motive oil and oil filter
   Check of a state and replacement of the hoses located in a motive compartment
   Rotation of wheels
   Greasing of components of the chassis
   Check of a condition of components of system of production of the fulfilled gases
   Check of a condition of seat belts
   Check of a condition of components of a suspension bracket
   Check of a condition of components of the steering drive
   Check and adjustment of composition of mix of idling, - a stern of the models equipped with the catalytic converter
   Check of a condition of protective covers of hinges of power shafts
   Check of a state, adjustment of effort of a tension of belts of the drive of auxiliary units
   Check and adjustment of the antiretractable device
   Check of serviceability of functioning and adjustment of components of coupling
   Checks and adjustments of brake system
   Check of a condition of components of the cooling system
   Check of a state and replacement of cooling liquid of the engine
   Replacement of the filtering air cleaner element
   Check of a condition of components of a power supply system
   Replacement of brake liquid / pumping of a hydraulic path
   Replacement of ATF of automatic transmission
   Replacement of the RKPP transmission oil
   Replacement of greasings of back and forward differential
   Check of a state and replacement of a gas-distributing belt - l models 2.0 and 2.5
   Check and replacement of the fuel filter
   Check of a state and replacement of spark plugs and VV of an electrical wiring
   Check of wheel bearings
   Check of valvate gaps
   Replacement of belts of the drive of auxiliary units and replacement
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment









d9f1bda0


Greasing of components of the chassis

List of the materials necessary for greasing of components of the chassis

1 — Liquid motive oil - is used for greasing of door loops
2 — the Graphite aerosol - is used for greasing of castle cylinders

3 — Greasing - in the market the wide range of greasings of various type and the viscosity intended for pumping by means of the lubricant gun is presented
4 — the Lubricant gun - is intended for stuffing of components by greasing, is used complete with different nozzles and transitional hoses


 PERFORMANCE ORDER

1. Prepare a necessary reserve of greasing of the demanded grade and the lubricant gun for stuffing of hollow components.

 On some knots instead of lubricant unions caps can be established, - take care also of existence near at hand of a set of unions, - carving nipple nozzles of various form providing adequate access practically to any component are issued.

2. Having glanced under the car, find lubricant unions of components of the steering drive, a suspension bracket and the transmission line. Usually unions are included in the regular package of such knots, as tips of steering drafts and cardan hinges. If instead of unions caps are established, instead of them it is necessary to screw the prepared nipple nozzles.
3. The car also establish to Poddomkratta it on the props got under a frame, or tire out its elevator.

 If assume to make rotation of wheels at this stage, do not forget to weaken fixing nuts before wheels are torn off from the earth.

4. For a gun nozzle clearing from dirt squeeze out a little greasing. Wipe a nozzle pure rags.
5. Prepare a stock of rags and start stuffing of components greasing.
6. Wipe the lubricant union and the component surface surrounding it pure rags, connect a nozzle of the gun to the union and start stuffing. Continue to pump greasing until it does not start exuding through joints of landing surfaces of a component.

 If greasing starts exuding through a gun nozzle, it is necessary to clean it and to pay special attention to clip density. In case of need replace the union.

7. Rags collect excess of greasing from a component surface and pass to stuffing of the following knot.
8. Continue stuffing of the sliding collar of the universal hinge of the driveshaft until greasing does not start exuding an assembly epiploon.
9. When stuffing cardan hinges of usual type greasing has to start exuding through joints of components of assembly.
10. Without getting out from under the car, wipe cables of the drive of the parking brake and grease with fingers their directing and executive levers.
11. At the corresponding complete set of the car apply greasing on a lithium basis on contact surfaces of persistent arms and adjusting bolts of assemblies of rotary fists.
12. Open a cowl and fill a little greasing for the chassis in the lock latch mechanism. Ask the assistant to extend against the stop the cowl lock otpuskaniye lever under the dashboard and grease all bared surfaces of a driving cable.
13. Liquid motive oil loops of all doors and a cowl.
14. For greasing of castle cylinders it is most convenient to use the graphite greasing delivered in aerosol barrels, - ask in shops of automobile accessories.
15. Grease with silicone greasing sealing tapes of doors for the purpose of protection them from premature wear.