Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car


Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
- Routine maintenance
   Schedule of routine maintenance of Subaru Legacy and Outback cars
   Specifications
   General information about settings and adjustments
   Check of levels of liquids (according to the Schedule of routine maintenance)
   Replacement of motive oil and oil filter
   Check of a state and replacement of the hoses located in a motive compartment
   Rotation of wheels
   Greasing of components of the chassis
   Check of a condition of components of system of production of the fulfilled gases
   Check of a condition of seat belts
   Check of a condition of components of a suspension bracket
   Check of a condition of components of the steering drive
   Check and adjustment of composition of mix of idling, - a stern of the models equipped with the catalytic converter
   Check of a condition of protective covers of hinges of power shafts
   Check of a state, adjustment of effort of a tension of belts of the drive of auxiliary units
   Check and adjustment of the antiretractable device
   Check of serviceability of functioning and adjustment of components of coupling
   Checks and adjustments of brake system
   Check of a condition of components of the cooling system
   Check of a state and replacement of cooling liquid of the engine
   Replacement of the filtering air cleaner element
   Check of a condition of components of a power supply system
   Replacement of brake liquid / pumping of a hydraulic path
   Replacement of ATF of automatic transmission
   Replacement of the RKPP transmission oil
   Replacement of greasings of back and forward differential
   Check of a state and replacement of a gas-distributing belt - l models 2.0 and 2.5
   Check and replacement of the fuel filter
   Check of a state and replacement of spark plugs and VV of an electrical wiring
   Check of wheel bearings
   Check of valvate gaps
   Replacement of belts of the drive of auxiliary units and replacement
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



d9f1bda0

Replacement of brake liquid / pumping of a hydraulic path

Sequence of pumping

1 — the Brake mechanism of the right forward wheel
2 — the Brake mechanism of the left back wheel
3 — the Brake mechanism of the left forward wheel

4 — the Brake mechanism of the right back wheel
5 — the GTTs Secondary camera
6 — the GTTs Primary camera


 PERFORMANCE ORDER

 Performance of this procedure will require the help of the assistant, or it is necessary to get a special set for pumping of brake system by forces of one person - ask in shops of automobile accessories.

1. The car also establish to Poddomkratta it on props.
2. Remove all wheels.
3. By means of a syringe or a rubber pear pump out brake fluid from the tank of the main brake cylinder (MBC).
4. Fill in fresh brake fluid of the demanded grade in the tank, - try not to allow hits to the brake highway of dirt.

 Mixing of hydraulic liquids of various grade is fraught with dangerous decrease in efficiency of functioning of brake system!

5. Connect one end of a vinyl tube of suitable diameter to the gate of pumping of a support of the brake mechanism of the right forward wheel, lower the second end of a tube in the drain capacity of the adequate size.

 In order to avoid hit of brake fluid on components of the brake mechanism, before an otpuskaniye wrap up the drain gate old rags.

6. Ask the assistant 2-3 times to press slowly a brake pedal, then to record it in the squeezed-out situation.
7. Release the pumping gate approximately on 1/4 turns and let out a small amount of hydraulic liquid in drain capacity, then again tighten the gate.
8. Continue to act in the manner described in two previous paragraphs until liquid, pure, transparent, free from air bubbles, does not start following from a tube.

 Do not forget to watch liquid level in the GTTs tank, without allowing its excessive lowering, - in time add fresh liquid!

9. Having finished pumping, tighten the gate with the demanded effort at the pressed pedal of a foot brake.
10. Working in a similar manner, in strictly certain order consistently pump over brake mechanisms of the remained wheels and both GTTs cameras.
11. In summary, squeeze out a pedal of a foot brake with effort about 30 kgfs and, holding its pressed within about 20 seconds, make sure of lack of an excessive side play of a pedal, then examine gates of pumping of brake mechanisms, GTTs and all nipple sockets of a hydraulic path on existence of signs of development of leaks. In case of need make the corresponding corrections / replace defective components.
12. Establish to the place of a wheel, lower the car on the earth during short (2-3 km) trips check serviceability of functioning of brake system.