Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
- Routine maintenance
   Schedule of routine maintenance of Subaru Legacy and Outback cars
   Specifications
   General information about settings and adjustments
   Check of levels of liquids (according to the Schedule of routine maintenance)
   Replacement of motive oil and oil filter
   Check of a state and replacement of the hoses located in a motive compartment
   Rotation of wheels
   Greasing of components of the chassis
   Check of a condition of components of system of production of the fulfilled gases
   Check of a condition of seat belts
   Check of a condition of components of a suspension bracket
   Check of a condition of components of the steering drive
   Check and adjustment of composition of mix of idling, - a stern of the models equipped with the catalytic converter
   Check of a condition of protective covers of hinges of power shafts
   Check of a state, adjustment of effort of a tension of belts of the drive of auxiliary units
   Check and adjustment of the antiretractable device
   Check of serviceability of functioning and adjustment of components of coupling
   Checks and adjustments of brake system
   Check of a condition of components of the cooling system
   Check of a state and replacement of cooling liquid of the engine
   Replacement of the filtering air cleaner element
   Check of a condition of components of a power supply system
   Replacement of brake liquid / pumping of a hydraulic path
   Replacement of ATF of automatic transmission
   Replacement of the RKPP transmission oil
   Replacement of greasings of back and forward differential
   Check of a state and replacement of a gas-distributing belt - l models 2.0 and 2.5
   Check and replacement of the fuel filter
   Check of a state and replacement of spark plugs and VV of an electrical wiring
   Check of wheel bearings
   Check of valvate gaps
   Replacement of belts of the drive of auxiliary units and replacement
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




d9f1bda0



Check of a condition of components of the steering drive

Steering wheel

 PERFORMANCE ORDER

1. Establish a steering wheel in neutral (central) situation and make sure of straightforwardness of installation of naves of forward wheels.

2. Ask the assistant to rotate slightly a steering wheel to the right-to the left and try to estimate the moments of the beginning of turn of wheels visually. Measure the size of a free wheeling of a steering wheel (on the outer side of a rim), compare results of measurements to requirements of Specifications.

3. Make sure that the axial side play of a steering wheel on a shaft of a column does not exceed 0.5 mm.
4. Make trial runs of the car with check of the following parameters:

a) Rotary effort: resistance of the helmsman of wheels to rotation has to be uniform and identical on all length of the course;
b) Withdrawals of a steering wheel (course stability of the vehicle): the steering wheel should not leave spontaneously in any of the parties at the movement on an equal horizontal covering;
c) Beating of a steering wheel: the beating of a steering wheel during the movement has to be absent completely;
d) Return of a steering wheel: at the helmsman's otpuskaniye upon completion of turn it has to come back to neutral situation.


Hinge of a steering shaft

 PERFORMANCE ORDER

1. At an excessive free wheeling of a steering wheel, disconnect the cardan hinge of a steering shaft and check it for existence of side plays. Estimate a condition of sealing and shlitsevy surfaces.

2. In case of need tighten fixing bolts of hinged assembly with the demanded effort (24 Nanometers).


Steering mechanism

 PERFORMANCE ORDER

 Performance of these checks will require the help of the assistant.

1. Tire out the car on an equal horizontal platform, whenever possible with a hard coating and serially turn a steering wheel on 90 ° in each of the directions.

2. At the turned steering wheel visually estimate a condition of protective covers of the steering mechanism. Estimate correctness of landing and reliability of fastening of protective covers, grease sealing sponges of covers. In case of need eliminate the deformations of covers which arose during adjustment of convergence of wheels, - develop the outer edge of the twisted cover in the relevant party.

3. Check reliability of a tightening of fixing bolts, in case of need tighten fixture with the demanded effort (59 Nanometers).

4. Quickly rotating a steering wheel to the right-to the left, estimate correctness of a side play of gearing of elements of rack transfer of the steering mechanism. If functioning of rack transfer is followed by extraneous noises, make adjustment of a side play of gearing:
a) Tighten the adjusting screw with effort of 7.4 Nanometers, then again release it, - repeat this procedure twice;
b) Tighten the adjusting screw with effort of 7.4 Nanometers and then weaken it, having turned on 25 є back;
c) Grease at least 1/3 full perimeters of a carving surface of the adjusting screw with liquid greasing;
d) Screw a kontryashchy nut and, holding the adjusting screw a wrench, tighten a lock-nut with the demanded effort, - use ST 926230000 key.


Steering drafts

 PERFORMANCE ORDER

1. Check steering drafts and their tips for existence of bends, scratches and other mechanical damages.

2. Check reliability of fastening of tips to rotary fists, estimate a condition of boots and check side plays of spherical fingers. In case of need tighten koronchaty nuts of fastening of tips with the demanded effort, then bring up them within a corner 60 ° before combination of shplintovy openings. Block nuts new forelocks.
3. Check effort of a tightening of lock nuts of tips of steering drafts. In case of need tighten nuts with the demanded effort.


Hoses and elements of fixture of the steering pump

 PERFORMANCE ORDER

1. Check pressure head and returnable hoses of the steering pump for existence of cracks, swellings and other damages. Replace defective hoses.
2. At the cold engine check effort of a tightening of bolts and nuts of fastening of the pump.