Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car

Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
- Routine maintenance
   Schedule of routine maintenance of Subaru Legacy and Outback cars
   General information about settings and adjustments
   Check of levels of liquids (according to the Schedule of routine maintenance)
   Replacement of motive oil and oil filter
   Check of a state and replacement of the hoses located in a motive compartment
   Rotation of wheels
   Greasing of components of the chassis
   Check of a condition of components of system of production of the fulfilled gases
   Check of a condition of seat belts
   Check of a condition of components of a suspension bracket
   Check of a condition of components of the steering drive
   Check and adjustment of composition of mix of idling, - a stern of the models equipped with the catalytic converter
   Check of a condition of protective covers of hinges of power shafts
   Check of a state, adjustment of effort of a tension of belts of the drive of auxiliary units
   Check and adjustment of the antiretractable device
   Check of serviceability of functioning and adjustment of components of coupling
   Checks and adjustments of brake system
   Check of a condition of components of the cooling system
   Check of a state and replacement of cooling liquid of the engine
   Replacement of the filtering air cleaner element
   Check of a condition of components of a power supply system
   Replacement of brake liquid / pumping of a hydraulic path
   Replacement of ATF of automatic transmission
   Replacement of the RKPP transmission oil
   Replacement of greasings of back and forward differential
   Check of a state and replacement of a gas-distributing belt - l models 2.0 and 2.5
   Check and replacement of the fuel filter
   Check of a state and replacement of spark plugs and VV of an electrical wiring
   Check of wheel bearings
   Check of valvate gaps
   Replacement of belts of the drive of auxiliary units and replacement
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


Replacement of the filtering air cleaner element


 Do not try to wash out the filtering air cleaner element. Paper of which the element is made, is impregnated with the special nonflammable, slowly evaporating viscous liquid doing it frost-resistant and prolonging element service life.

Dirt sticks to the viscous liquid filling porous structure of paper that interferes with its penetration in an inlet path. Washing of an element involves loss of impregnation and, - as a result, - noticeable decrease in efficiency of functioning of the air cleaner.
1. Replacement of the filtering element is made regularly according to the schedule of routine maintenance of the car. During operation of the car the condition of the filter has to be checked rather often, in particular in the conditions of strongly dusty district.
2. On l models 2.0 and 2.5 the air cleaner is fixed in back part of a motive compartment on the center of a partition, on models of 3.0 l – in the right back corner.
3. Give bolts of fastening of the air cleaner to basic drains (l models 2.0 and 2.5), release spring clamps of a cover of the air cleaner, disconnect everything the hoses stirring to performance procedures and uncover, - try not to allow falling in a casing of the air cleaner of foreign subjects.

4. Take the filtering element and wipe internal walls of a casing pure rags.

5. Visually estimate a condition of the filtering element, in case of strong pollution make replacement.

 In order to avoid premature wear of internal components of the engine and emergence of flashes in a final path do not operate the car with the taken air filter!

6. Establish the replaceable filtering element, track correctness of its landing in a casing.

7. Make assembly as it should be, the return to removal. Tighten fixing bolts with the demanded effort.

 On models of 3.0 l before installation of a cover of the air cleaner bring lock uvulas from the back party of a cover to reception grooves of a casing, then latch clamps.