Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
- Routine maintenance
   Schedule of routine maintenance of Subaru Legacy and Outback cars
   Specifications
   General information about settings and adjustments
   Check of levels of liquids (according to the Schedule of routine maintenance)
   Replacement of motive oil and oil filter
   Check of a state and replacement of the hoses located in a motive compartment
   Rotation of wheels
   Greasing of components of the chassis
   Check of a condition of components of system of production of the fulfilled gases
   Check of a condition of seat belts
   Check of a condition of components of a suspension bracket
   Check of a condition of components of the steering drive
   Check and adjustment of composition of mix of idling, - a stern of the models equipped with the catalytic converter
   Check of a condition of protective covers of hinges of power shafts
   Check of a state, adjustment of effort of a tension of belts of the drive of auxiliary units
   Check and adjustment of the antiretractable device
   Check of serviceability of functioning and adjustment of components of coupling
   Checks and adjustments of brake system
   Check of a condition of components of the cooling system
   Check of a state and replacement of cooling liquid of the engine
   Replacement of the filtering air cleaner element
   Check of a condition of components of a power supply system
   Replacement of brake liquid / pumping of a hydraulic path
   Replacement of ATF of automatic transmission
   Replacement of the RKPP transmission oil
   Replacement of greasings of back and forward differential
   Check of a state and replacement of a gas-distributing belt - l models 2.0 and 2.5
   Check and replacement of the fuel filter
   Check of a state and replacement of spark plugs and VV of an electrical wiring
   Check of wheel bearings
   Check of valvate gaps
   Replacement of belts of the drive of auxiliary units and replacement
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




d9f1bda0

Replacement of belts of the drive of auxiliary units and replacement

Scheme of installation of a forward driving belt (drive of the generator and steering pump)

And — the Lock (through) bolt
In — the Coupling (adjusting) bolt

With — the Forward driving belt


Scheme of installation of a back driving belt (K/V compressor drive)

And — the Lock nut
In — the Coupling (adjusting) bolt

With — the Back driving belt


L models 2.0 and 2.5

 PERFORMANCE ORDER

1. Turn out fixing bolts and uncover a belt(s) of the drive of auxiliary units. Carefully wipe surfaces of a belt and driving pulleys, having completely cleared them of oil/moisture traces.

2. Weaken at first lock (through), then coupling (adjusting) bolts and take off a forward belt of the drive of the generator and steering pump.
3. Working in a similar manner, take off a back belt of the drive of the К/В compressor.
4. Authors of the present manual recommend to make replacement of both driving belts at the same time in view of approximately identical speed of their wear.

 On some models from below to a cowl the label with the scheme of laying of driving belts fastens.

5. Upon purchase of new belts take with yourself old as samples - replaceable belts have to correspond strictly removed from the car on a standard size.
6. Establish a new belt of the drive of the K/V compressor, - track correctness of its landing on pulleys. A tightening of a coupling (adjusting) bolt adjust effort of its tension (see the Section Check of a State, adjustment of effort of a tension of belts of the drive of auxiliary units). Having finished adjustment, tighten with the demanded effort through a lock nut.
7. Establish a new belt of the drive of the generator and steering pump, - track correctness of its landing on pulleys. A tightening of a coupling (adjusting) bolt adjust effort of its tension (see the Section Check of a State, adjustment of effort of a tension of belts of the drive of auxiliary units). Having finished adjustment, tighten a through lock bolt with the demanded effort.


Models of 3.0 l

The scheme of installation of a belt of the drive of auxiliary units and elements of its fastening on models of 3.0 l

1 — the Tape of a driving belt
2 — the Protective cover
3 — Natyazhitel of a driving belt
4 — the Arm of the steering pump
5 — the Generator
6 — the Plate of fastening of the generator
7 — the K/V compressor Support
8 — the Intermediate roller

9 — the Clamping washer of a tension roller

Efforts of a tightening of the carving
connections, Nanometer

T1: 6.4
T2: 20
T3: 25
T4: 33


The scheme of laying of a belt of the drive of auxiliary units on models of 3.0 l

1 — the Pulley of the steering pump
2 — the Regulator of a natyazhitel of a driving belt
3 — the Pulley of a cranked shaft

4 — the K/V compressor Pulley
5 — the Tension roller
6 — a generator Pulley


 PERFORMANCE ORDER

1. Details of installation of a belt of the drive of auxiliary units on models of 3.0 l are shown on an illustration.

2. By turning of the fastening of a natyazhitel of a special key which is put on a bolt clockwise weaken effort of a tension of a belt.

3. Installation is made upside-down, - track correctness of landing of a belt on pulleys.
4. A tightening of a coupling (adjusting) bolt adjust effort of its tension (see the Section Check of a State, adjustment of effort of a tension of belts of the drive of auxiliary units). Having finished adjustment, tighten a through lock bolt with the demanded effort.
Establish a new driving belt, watching correctness of its landing on pulleys, and tighten an assembly bolt of a natyazhitel of a driving belt by turn of a key counterclockwise for the correct tension of a belt.