Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
- Manual box and differential
   Specifications
   The mechanism of blocking of inclusion of a reverse gear - the device and the principle of functioning
   Interaxal differential - the device and the principle of functioning
   Removal and installation of transmission assembly
   Check of a state and replacement of elements of support of a suspension bracket of transmission assembly
   Check of a state and replacement of an epiploon
   Removal, installation and check of a condition of sensors switches
   Removal, installation and check of a condition of the sensor of the speed (VSS)
   Preparation for performance of capital repairs of RKPP
   Removal, service and installation of a transfer case and lengthening of transmission
   Removal, service and installation of the leading gear wheel of the distributing mechanism
   Removal, service and installation of the conducted gear wheel of the distributing mechanism
   Removal, service and installation of interaxal differential
   Removal, service, installation and adjustment of assembly of the mechanism of blocking of inclusion of a reverse gear
   Removal, installation and check of a condition of a case of transmission assembly
   Removal, service, installation and adjustment of primary shaft of RKPP
   Removal, service and installation of an entrance shaft of RKPP (model with an additional two-level reducer)
   Removal, service and installation of assembly of a shaft of the leading gear wheel of the main transfer of the drive of forward wheels
   Removal, service, installation and adjustment of forward differential
   Removal, installation and check of a condition of a gear wheel of the drive of a speedometer
   Removal, installation and adjustment of an intermediate gear wheel of a reverse gear
   Removal, installation, check and adjustment of assembly of gear wheels of a two-level reducer
   Removal, check of a state and installation of forks and rods of gear shifting
   Removal, service and installation of the lever of gear shifting of RKPP
   Removal, service and installation of the lever of switching of the Hi/Lo modes of an additional two-level reducer
   Removal, service and installation of hummock draft of the drive of switching of the modes of a two-level reducer
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment









d9f1bda0


Removal, installation and check of a condition of the sensor of the speed (VSS)

REMOVAL

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. The car also establish to Poddomkratta it on props.
3. Remove a collector with its receiver.
4. Separate the VSS socket.

5. Turn and remove VSS.

INSTALLATION

 PERFORMANCE ORDER

 The removed VSS is subject to replacement without fail. Before installation make sure of purity of an opening under landing of the sensor. Track correctness of combination of the thin end of a spline with a shponochny groove on a speedometer shaft pin.

1. Manually screw VSS in a landing opening, then tighten it with the demanded effort (5.9 Nanometers).
2. Connect the contact socket of an electrical wiring of the sensor.
3. Further installation is made as it should be, the return to an order of dismantle of components.

CHECK



 PERFORMANCE ORDER

1. Make sure of serviceability of functioning of a speedometer. At positive results of check pass to the following stage, otherwise measure speedometer resistance. The result of measurement between sinus and cosine plugs has to make 208 ± 8 Ohms, otherwise follows will replace the fan and assembly from a fuel consumption measuring instrument. If a speedometer as it should be, replace the printed-circuit board of a combination of devices.

2. Switch off ignition and measure resistance between the plug No. 24 of the contact ECM (B135) socket and the plug No. 13 of the contact socket of a combination of devices (i10). If the result of measurement makes less than 10 Ohms, replace the ECM socket, otherwise eliminate break of an electrical wiring or violation of quality of contact connections in B135/B36 sockets.