Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
- Manual box and differential
   Specifications
   The mechanism of blocking of inclusion of a reverse gear - the device and the principle of functioning
   Interaxal differential - the device and the principle of functioning
   Removal and installation of transmission assembly
   Check of a state and replacement of elements of support of a suspension bracket of transmission assembly
   Check of a state and replacement of an epiploon
   Removal, installation and check of a condition of sensors switches
   Removal, installation and check of a condition of the sensor of the speed (VSS)
   Preparation for performance of capital repairs of RKPP
   Removal, service and installation of a transfer case and lengthening of transmission
   Removal, service and installation of the leading gear wheel of the distributing mechanism
   Removal, service and installation of the conducted gear wheel of the distributing mechanism
   Removal, service and installation of interaxal differential
   Removal, service, installation and adjustment of assembly of the mechanism of blocking of inclusion of a reverse gear
   Removal, installation and check of a condition of a case of transmission assembly
   Removal, service, installation and adjustment of primary shaft of RKPP
   Removal, service and installation of an entrance shaft of RKPP (model with an additional two-level reducer)
   Removal, service and installation of assembly of a shaft of the leading gear wheel of the main transfer of the drive of forward wheels
   Removal, service, installation and adjustment of forward differential
   Removal, installation and check of a condition of a gear wheel of the drive of a speedometer
   Removal, installation and adjustment of an intermediate gear wheel of a reverse gear
   Removal, installation, check and adjustment of assembly of gear wheels of a two-level reducer
   Removal, check of a state and installation of forks and rods of gear shifting
   Removal, service and installation of the lever of gear shifting of RKPP
   Removal, service and installation of the lever of switching of the Hi/Lo modes of an additional two-level reducer
   Removal, service and installation of hummock draft of the drive of switching of the modes of a two-level reducer
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment









d9f1bda0


Removal, service and installation of the lever of switching of the Hi/Lo modes of an additional two-level reducer

Design of the lever of switching of the modes of a two-level reducer

1 — the Handle
2 — the Pillow
3 — the Plate
4 — the Plug
5 — Trosovaya draft
6 — the Spring
7 — the Lever
8 — the Clamp
9 — the Pin

10 — the Clamp

Efforts of a tightening of threaded connections, Nanometer

T1: 1.6
T2: 18

REMOVAL

 PERFORMANCE ORDER

1. Install the lever of switching of the modes in the situation "Hi".

2. Remove the lever handle.

3. Remove the central console (see the Head Kuzov).

4. Turn out a bolt of fastening of assembly of the lever of switching of the modes to a body.


5. Give a flantsovanny nut, take a clamp (8) and disconnect from lever assembly draft (5).

DISMANTLING

Remove the lever of switching of the modes of a 2-staged reducer

And — the Washer
In — the Plug
With — the Plate

D — the Pillow
E — the Lever
F — the Bolt


 PERFORMANCE ORDER

1. Remove a spring.

2. Remove the lever, a cap and the plug.

ASSEMBLY

 PERFORMANCE ORDER

Assembly is made as it should be, the return to an order of dismantle of components. The effort of a tightening of a fixing bolt makes 1.6 Nanometers. In summary check smoothness of the course of the lever. In case of need make necessary recovery repair, replace the failed components.

INSTALLATION

 PERFORMANCE ORDER

1. Transfer the lever of switching of the modes to the situation "Hi".

2. Track that the bolt of a tip of draft got to a lever cut. Tighten a flantsovanny nut with the demanded effort (18 Nanometers).

3. Further installation is made as it should be, the return to an order of dismantle of components. Make sure of smoothness of the course of the lever and serviceability of functioning of the mechanism of switching of the modes.