Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car


Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
- Manual box and differential
   Specifications
   The mechanism of blocking of inclusion of a reverse gear - the device and the principle of functioning
   Interaxal differential - the device and the principle of functioning
   Removal and installation of transmission assembly
   Check of a state and replacement of elements of support of a suspension bracket of transmission assembly
   Check of a state and replacement of an epiploon
   Removal, installation and check of a condition of sensors switches
   Removal, installation and check of a condition of the sensor of the speed (VSS)
   Preparation for performance of capital repairs of RKPP
   Removal, service and installation of a transfer case and lengthening of transmission
   Removal, service and installation of the leading gear wheel of the distributing mechanism
   Removal, service and installation of the conducted gear wheel of the distributing mechanism
   Removal, service and installation of interaxal differential
   Removal, service, installation and adjustment of assembly of the mechanism of blocking of inclusion of a reverse gear
   Removal, installation and check of a condition of a case of transmission assembly
   Removal, service, installation and adjustment of primary shaft of RKPP
   Removal, service and installation of an entrance shaft of RKPP (model with an additional two-level reducer)
   Removal, service and installation of assembly of a shaft of the leading gear wheel of the main transfer of the drive of forward wheels
   Removal, service, installation and adjustment of forward differential
   Removal, installation and check of a condition of a gear wheel of the drive of a speedometer
   Removal, installation and adjustment of an intermediate gear wheel of a reverse gear
   Removal, installation, check and adjustment of assembly of gear wheels of a two-level reducer
   Removal, check of a state and installation of forks and rods of gear shifting
   Removal, service and installation of the lever of gear shifting of RKPP
   Removal, service and installation of the lever of switching of the Hi/Lo modes of an additional two-level reducer
   Removal, service and installation of hummock draft of the drive of switching of the modes of a two-level reducer
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



d9f1bda0

Check of a state and replacement of elements of support of a suspension bracket of transmission assembly

Details of installation of support of a suspension bracket of transmission assembly are shown on an illustration.

Before removal of elements of support of a suspension bracket of transmission assembly disconnect a negative wire from the battery.

1 — the Limiter of raskachivaniye
2 — the Remote plug
3 — the Rubber pillow of C
4 — the Forward plate
5 — the Damper of dynamic fluctuations
6 — the Back rubber pillow
7 — the Back cross beam
8 — the Rubber pillow of D
9 — the Central beam
10 — the Back plate
11 — the Forward cross beam (Outback models)

12 — the Forward cross beam (Legacy models)

Efforts of a tightening of threaded connections, Nanometer

T1: 7.5
T2: 35
T3: 50
T4: 58
T5: 70
T6: 140

REMOVAL

Limiter of rocking of the power unit

 PERFORMANCE ORDER

1. Remove the air cleaner
2. Remove the limiter of rocking of the power unit (see the Section Removal and installation of transmission assembly).


Cross beam and rubber pillows

 PERFORMANCE ORDER

1. The car also establish to Poddomkratta it on props.
2. Sections of system of production of the fulfilled gases (see the Head of the Power supply system and release).
3. Uncover the thermofilter.
4. Prop up a transmission a transmission jack (see the Section Removal and installation of transmission assembly).
5. Remove a back cross beam.
6. Separate a rubber pillow of a back support of a suspension bracket of the power unit.

CHECK

 PERFORMANCE ORDER

Make sure of lack of deformations of metal components, check rubber elements for existence of signs of aging of material, cracks, cuts and other damages. Make necessary repair, replace the failed details.

INSTALLATION

 PERFORMANCE ORDER

Installation is made as it should be, the return to an order of dismantle of components. Track that all fixture was tightened with the demanded effort.