Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
- Manual box and differential
   Specifications
   The mechanism of blocking of inclusion of a reverse gear - the device and the principle of functioning
   Interaxal differential - the device and the principle of functioning
   Removal and installation of transmission assembly
   Check of a state and replacement of elements of support of a suspension bracket of transmission assembly
   Check of a state and replacement of an epiploon
   Removal, installation and check of a condition of sensors switches
   Removal, installation and check of a condition of the sensor of the speed (VSS)
   Preparation for performance of capital repairs of RKPP
   Removal, service and installation of a transfer case and lengthening of transmission
   Removal, service and installation of the leading gear wheel of the distributing mechanism
   Removal, service and installation of the conducted gear wheel of the distributing mechanism
   Removal, service and installation of interaxal differential
   Removal, service, installation and adjustment of assembly of the mechanism of blocking of inclusion of a reverse gear
   Removal, installation and check of a condition of a case of transmission assembly
   Removal, service, installation and adjustment of primary shaft of RKPP
   Removal, service and installation of an entrance shaft of RKPP (model with an additional two-level reducer)
   Removal, service and installation of assembly of a shaft of the leading gear wheel of the main transfer of the drive of forward wheels
   Removal, service, installation and adjustment of forward differential
   Removal, installation and check of a condition of a gear wheel of the drive of a speedometer
   Removal, installation and adjustment of an intermediate gear wheel of a reverse gear
   Removal, installation, check and adjustment of assembly of gear wheels of a two-level reducer
   Removal, check of a state and installation of forks and rods of gear shifting
   Removal, service and installation of the lever of gear shifting of RKPP
   Removal, service and installation of the lever of switching of the Hi/Lo modes of an additional two-level reducer
   Removal, service and installation of hummock draft of the drive of switching of the modes of a two-level reducer
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




d9f1bda0



Removal, service and installation of hummock draft of the drive of switching of the modes of a two-level reducer

REMOVAL

 PERFORMANCE ORDER

1. Remove the lever of switching of the modes (see the Section Removal, service and installation of the lever of switching of the Hi/Lo modes of an additional two-level reducer).
2. Remove the air cleaner case with an air inlet sleeve (see the Head of the Power supply system and release).

3. Remove a spring lock ring and take a pin of fastening of hummock draft.

And — the Spring lock ring
In — the Pin
With — the Nut

4. Release a fixing nut and release hummock draft from a basic arm.

5. Take draft from under the car.

6. Check draft for existence of damages, in case of need make its replacement.

INSTALLATION

 PERFORMANCE ORDER

Installation is made as it should be, the return to an order of dismantle of components.

CHECK

 PERFORMANCE ORDER

1. Make sure of serviceability of switching of the Hi and Lo modes. In case of need make adjustment of driving draft (see below).
2. Make sure of smoothness of the course of a driving cable. In case of identification of points of jamming make necessary recovery repair, or replace draft assembly.

ADJUSTMENT

 PERFORMANCE ORDER

1. Transfer the lever of switching of the modes to the situation "Hi".
2. Remove the handle of the lever of switching of the modes (see the Section Removal, service and installation of the lever of switching of the Hi/Lo modes of an additional two-level reducer).
3. Remove the central console (see the Head Kuzov).
4. Weaken a nut.
5. Be convinced that transmission is in the situation "Hi", - in case of need achieve demanded result by procrastination of hummock draft, then tighten a nut with the demanded effort (18 Nanometers).
6. Check serviceability of switching of the modes of a 2-staged reducer, in case of need repeat adjustment.