Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
Specifications
Search of causes of failures of electric equipment
Safety locks - the general information
Chain breakers - the general information
The relay - the general information and check of serviceability of functioning
Details of laying of an onboard electrical wiring
System of additional safety (SRS) - the device and the principle of functioning
Diagnostics of malfunctions of SRS
Removal and installation of the SRS components
Control system of speed (tempostat) - the device and the principle of functioning
Check of serviceability of functioning of components and problem diagnostics of a tempostat
Removal, check of a state and installation of components of a control system of speed
Combination of devices - the general information and the principle of functioning of components
Problem diagnostics of components of a combination of devices
Removal, service and installation of a combination of devices, check of a condition of components
Heating of back glass and rear-view mirrors - the general information, check of serviceability of functioning of components, recovery repair of a thermoelectric heating element
Heating of brushes of screen wipers - the general information, check of serviceability of functioning of components, recovery repair of a thermoelectric heating element
Removal, check of a state and installation of switches of management of functioning of the electric drive of regulators of window regulators
The electric drive of rear-view mirrors - check of serviceability of functioning
Removal check and installation of the switch of management of functioning of the electric drive of external rear-view mirrors
Removal, check of a state and installation of the switch of management of functioning of the electric drive of the top hatch
Removal, check of a state and installation of the combined understeering switches
Check of serviceability of functioning of electric motors of the drive of screen wipers, removal, check and installation of the operating relay of a back screen wiper on the Legacy Station wagon/Outback models
Check of the relay and switches of lighting and alarm devices
Removal and installation of illuminants, replacement of lamps
Removal, check of a state and installation of horns and switch of a horn
Check of a state and replacement of contact group of the switch of ignition
The uniform lock - the device, the principle of functioning, diagnostics of malfunctions
Removal, check of a state and installation of components of the uniform lock
System of an immobilization of the engine - the device, the principle of functioning, diagnostics of malfunctions
Removal and installation of components of system of an immobilization of the engine
Removal and installation of assembly of the radio receiver
Removal and installation of loudspeakers
Check of a state and recovery repair of the window antenna of the radio receiver
Removal, installation and check of a condition of the antenna amplifier of the radio receiver
Removal and installation of the lighter
+ Schemes of electric connections
|
Removal and installation of illuminants, replacement of lamps
Assemblies of block headlights
Removal and installation
|
|
|
1. Disconnect a negative wire from the battery.
2. At service of the right block headlight remove an air inlet (see the Section Service of Components of an inlet air path of the Head of the Cooling system, heating).
|
|
3. Disunite the contact socket of an electrical wiring.
And — the Adjusting bolt
In — the Adjusting bolt |
|
|
4. Turn out three fixing bolts and remove a block headlight. |
5. Installation is made upside-down. |
|
Adjustment
|
|
|
|
Adjustment of headlights has to be made at completely filled fuel tank and with the person on a driver's place. |
|
|
Before performance of correction of a headlight it is necessary to extinguish. When checking correctness of the executed adjustments of a headlight should not join more than for 2 minutes! |
1. Make sure that the bearing body elements of a front of the car around installation of block headlights are not deformed and not damaged as a result of collision.
2. Park the car on an equal horizontal platform on removal about 3 meters from a vertical wall, perpendicular to the last.
3. Check correctness of a rating of tires, in case of need make the corresponding adjustments.
4. Shake car corners for shrinkage of elements of a suspension bracket.
|
|
5. Transfer the switch of the proofreader of headlights to the situation "0" and, rotation of screws vertical (And) and horizontal (In) adjustments make adjustment of provision of block headlights according to the requirements stipulated on an illustration and in table 40. |
|
|
Table 40
Replacement of lamps
Lamps of headlights
|
|
|
|
When burning halogen lamps are warmed to high temperature in this connection hit on glass of a flask of dirt and fatty spots leads to reduction of service life of a lamp, - try not to touch a lamp barehanded! |
1. Disconnect a negative wire from the battery.
2. At service of the right block headlight remove an air inlet (see the Section Service of Components of an inlet air path of the Head of the Cooling system, heating).
|
|
4. Disunite the contact socket of an electrical wiring of the corresponding lamp |
5. Wring out the spring holder and take a lamp from the boss.
6. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
Lamps of forward indexes of turns
|
|
|
1. Remove assembly of a block headlight (see above).
|
|
2. Turn a cartridge and take a lamp. |
3. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
Lamps of forward parking fires
|
|
|
1. Remove assembly of a block headlight (see above).
|
|
2. Turn a cartridge and take a lamp. |
3. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
Fog lights
Removal and installation
|
|
|
Disconnect a negative wire from the battery. |
|
Legacy models
|
|
|
|
1. Release two clamps and lower the deflector panel. |
|
|
2. Disconnect an electrical wiring, turn out fixing bolts and remove assembly of a fog light. |
3. Installation is made upside-down. |
|
Outback models
|
|
|
|
1. Turn counterclockwise and remove a protective lattice of a lens of a fog light. |
|
|
2. Turn out fixing bolts. |
3. Release two clamps and lower the deflector panel.
|
|
4. Disunite the contact socket of an electrical wiring, give fixing gayku remove assembly of a fog light.
and — the Contact socket of an electrical wiring
b — the Fixing nut |
5. Installation is made upside-down. |
|
Replacement of lamps
Legacy models
|
|
|
1. Disconnect a negative wire from the battery.
2. Release two clamps and lower the deflector panel.
|
|
3. Remove a back cover of assembly of a fog light. |
4. Remove the spring holder and take a lamp
5. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
Outback models
|
|
|
1. Remove assembly of a fog light (see above).
|
|
2. Turn out fixing screws and remove a back cover. |
3. Disconnect an electrical wiring, remove the spring holder and take a lamp.
4. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
The back combined lamps
Disconnect a negative wire from the battery.
Removal and installation
Body sections of lantern assemblies
Sedan models Legacy
|
|
|
1. Release clamps and remove the back panel of finishing of the lower aperture of a luggage compartment.
2. Remove an angular hook and open back lateral section of the panel of finishing of a luggage compartment.
|
|
3. Give three fixing nuts and, having disunited the contact socket of an electrical wiring, remove assembly of the back combined lamp. |
4. Installation is made upside-down. |
|
Legacy Station wagon/Outback models
|
|
|
1. Remove two covers of back lateral panels of internal finishing (see the Section Removal and installation of elements of internal finishing).
|
|
2. Give two fixing nuts and, having disunited the contact socket of an electrical wiring, remove assembly of the back combined lamp.
|
|
In order to avoid falling of nuts in the course of an otpuskaniye wind a tip of the service tool with couple of layers of a butyl tape. |
|
3. Installation is made upside-down. |
|
The section of lantern assembly established on a cover of luggage office / door of a back
Sedan models
|
|
|
1. Open a cover of a luggage compartment.
|
|
2. Remove a protective cover, disconnect the contact socket and remove a lamp.
And — the Protective cover
In — the Contact socket of an electrical wiring |
3. Installation is made upside-down. |
|
Legacy Station wagon/Outback models
|
|
|
1. Remove the lower panel of an upholstery of a door of a back.
|
|
2. Disconnect an electrical wiring, give fixing nuts and remove lantern assembly.
And — Fixing nuts |
3. Installation is made upside-down. |
|
Replacement of lamps
Lamps of stoplights / back marker lights and indexes of turns
Sedan models
|
|
|
1. Open a cover of a luggage compartment and remove a back cover of lantern assembly.
2. Turn out fixing screws and remove a back cover of lantern assembly.
|
|
3. Turn a cartridge and take the lamp needing replacement.
1 — a stoplight Lamp / a back marker light
2 — the Lamp of the back index of turn |
4. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
Legacy Station wagon/Outback models
|
|
|
1. Remove assembly of the back combined lamp (see above).
|
|
2. Turn a cartridge and take the lamp needing replacement.
1 — the Lamp of the back index of turn
2 — a stoplight Lamp / a back marker light |
3. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
Lamps of fires of a backing and foggy lamps
Sedan models
|
|
|
1. Open a cover of a luggage compartment and remove a back cover of lantern assembly.
|
|
2. Turn a cartridge and take the lamp needing replacement. |
3. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
Legacy Station wagon/Outback models
|
|
|
1. Open a door of a back and remove a back cover of lantern assembly.
|
|
2. Turn a cartridge and take the lamp needing replacement. |
3. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
Lamp of illumination of back registration plate
Replacement of a lamp
|
|
|
|
1. Turn out the fixing screw and remove a lens of lantern assembly.
And — Fixing screws
In — the Lens |
2. Take a lamp.
3. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications.
|
|
Stoplight of the top level
Replacement of a lamp
|
|
|
Disconnect a negative wire from the battery. |
|
Sedan models
|
|
|
|
1. Disunite the contact socket of an electrical wiring of a stoplight of the top level. |
2. Turn out fixing bolts and remove assembly of a stoplight.
3. Take the failed lamp.
4. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
Legacy Station wagon/Outback models
Details of installation of a stoplight of the top level on the Legacy Station wagon/Outback models
|
|
|
1. Having hooked a screw-driver, remove decorative caps, turn out fixing screws and remove a protective cover of assembly of a stoplight.
2. Turn out fixing screws and remove assembly of a stoplight of the top level.
3. Take the failed lamp.
4. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
Lateral repeaters of indexes of turns
Replacement of lamps
|
|
|
1. Disconnect a negative wire from the battery.
2. Having wrung out forward and having pulled outside, remove a lens of the lateral repeater from the body panel.
|
|
3. Disconnect an electrical wiring and take a lamp. |
4. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
The directed saloon lamps
Replacement of lamps
|
|
|
1. Disconnect a negative wire from the battery.
|
|
2. Having hooked a screw-driver, remove the panel of lenses, then turn out fixing screws, disconnect an electrical wiring and remove assemblies of the directed lamps.
And — the Panel of lenses of the directed lamps
In — Screws of fastening of assemblies of the directed lamps |
3. Take the lamps needing replacement.
4. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
Main saloon lamp
Replacement of a lamp
|
|
|
1. Disconnect a negative wire from the battery.
|
|
2. Having hooked, remove a plafond, then turn out screws of fastening of assembly of the lamp.
And — the Plafond
In — Screws of fastening of assembly of the lamp |
3. Take a lamp.
4. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
Lamp of illumination of a luggage compartment
|
|
|
Disconnect a negative wire from the battery. |
|
Replacement of a lamp
Sedan models
|
|
|
|
1. Disconnect an electrical wiring, remove a lens and take the failed lamp. |
2. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
Legacy Station wagon/Outback models
|
|
|
|
1. Having hooked, remove a plafond, then turn out screws of fastening of assembly of the lamp.
And — the Plafond
In — Screws of fastening of assembly of the lamp |
2. Take a lamp.
3. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
Lamp of illumination of the main ware box
Replacement of a lamp
|
|
|
1. Disconnect a negative wire from the battery.
2. Remove a ware box (see the Head Kuzov).
|
|
3. Disconnect an electrical wiring and remove a lamp. |
4. Take a lamp.
5. Installation is made upside-down, - track that the replaceable lamp corresponded on the to a standard size and working parameters to requirements of Specifications. |
|
|
|
