Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car


Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Specifications
   Search of causes of failures of electric equipment
   Safety locks - the general information
   Chain breakers - the general information
   The relay - the general information and check of serviceability of functioning
   Details of laying of an onboard electrical wiring
   System of additional safety (SRS) - the device and the principle of functioning
   Diagnostics of malfunctions of SRS
   Removal and installation of the SRS components
   Control system of speed (tempostat) - the device and the principle of functioning
   Check of serviceability of functioning of components and problem diagnostics of a tempostat
   Removal, check of a state and installation of components of a control system of speed
   Combination of devices - the general information and the principle of functioning of components
   Problem diagnostics of components of a combination of devices
   Removal, service and installation of a combination of devices, check of a condition of components
   Heating of back glass and rear-view mirrors - the general information, check of serviceability of functioning of components, recovery repair of a thermoelectric heating element
   Heating of brushes of screen wipers - the general information, check of serviceability of functioning of components, recovery repair of a thermoelectric heating element
   Removal, check of a state and installation of switches of management of functioning of the electric drive of regulators of window regulators
   The electric drive of rear-view mirrors - check of serviceability of functioning
   Removal check and installation of the switch of management of functioning of the electric drive of external rear-view mirrors
   Removal, check of a state and installation of the switch of management of functioning of the electric drive of the top hatch
   Removal, check of a state and installation of the combined understeering switches
   Check of serviceability of functioning of electric motors of the drive of screen wipers, removal, check and installation of the operating relay of a back screen wiper on the Legacy Station wagon/Outback models
   Check of the relay and switches of lighting and alarm devices
   Removal and installation of illuminants, replacement of lamps
   Removal, check of a state and installation of horns and switch of a horn
   Check of a state and replacement of contact group of the switch of ignition
   The uniform lock - the device, the principle of functioning, diagnostics of malfunctions
   Removal, check of a state and installation of components of the uniform lock
   System of an immobilization of the engine - the device, the principle of functioning, diagnostics of malfunctions
   Removal and installation of components of system of an immobilization of the engine
   Removal and installation of assembly of the radio receiver
   Removal and installation of loudspeakers
   Check of a state and recovery repair of the window antenna of the radio receiver
   Removal, installation and check of a condition of the antenna amplifier of the radio receiver
   Removal and installation of the lighter
   + Schemes of electric connections



d9f1bda0

Check of the relay and switches of lighting and alarm devices

 Schemes of connection of the relay and switches see in Schemes of electric connections.


Relay of head headlights

 PERFORMANCE ORDER

1. Connect the battery between No. No. 4 plugs (+) and 3 (-) of the relay and measure resistance between plugs No. No. 1 and 2. When giving food the result of measurement has to make less than 1 Ohm, at power off - more than 1 megohm.

2. Replace the faulty relay.


Relay of marker lights and illumination of devices

 PERFORMANCE ORDER

1. Check is made as well as for the relay of head headlights.
2. Replace the faulty relay.


Relay and switch of fog lights

Switch

 PERFORMANCE ORDER

1. Check correctness of distribution of conductivity between plugs No. No. 3 and 5 of the contact socket of the switch in both provisions of the last. At the closed switch the result of measurement has to make less than 1 Ohm, at opened, - more than 1 megohm.

2. Replace the faulty switch.


Relay and switch of back foggy lamps

Switch

 PERFORMANCE ORDER

1. Include ignition and head/fog lights.
2. Press the button of the switch and make sure of serviceability of activation of foggy lamps.
3. Replace the faulty switch.


Switch of back foggy lamps

See the Section Removal, check of a state and installation of the combined understeering switches.

Switch of the alarm system

 PERFORMANCE ORDER

1. Check correctness of distribution of conductivity between plugs of the contact socket of the switch in both provisions of the last (see the table).


2. Rumple the faulty switch.



Breaker of indexes of turns / alarm system

 PERFORMANCE ORDER

1. Connect the battery and a lamp of the index of turns to the breaker module. The uniform blinking of a lamp when giving in tension contour will testify to serviceability of functioning of the breaker.

2. The faulty breaker is subject to replacement.


The sensor switch of fires of a backing (model with RKPP)

 PERFORMANCE ORDER

1. Measure resistance between plugs No. 1 and No. 2 of the contact socket of the sensor switch. At the included reverse gear the result of measurement has to make less than 1 Ohm, in all other provisions of the lever of gear shifting, - more than 1 megohm.
3. Replace the faulty sensor switch.


The sensor switch of permission of start (model with AT)

 PERFORMANCE ORDER

1. Measure resistance between plugs No. 1 and No. 2 of the sensor switch. In the position "R" of the lever of the AT selector the result of measurement has to make less than 1 Ohm, in all other provisions of the lever, - more than 1 megohm.

2. Replace the faulty sensor switch.


Sensor switch of stoplights

 PERFORMANCE ORDER

1. Measure resistance between plugs No. 1 and No. 2 (models without tempostat)/№ 2 and No. 3 (models with tempostaty). At the squeezed-out pedal of a foot brake the result of measurement has to make less than 1 Ohm, at released, - more than 1 megohm.

2. Replace the faulty sensor switch.


Drive of adjustment of provision of headlights

Actuation mechanism

 PERFORMANCE ORDER

Include headlights and visually make sure of serviceability of functioning of the servo-driver at transfer of the operating switch to each of six working provisions (0-1-2-3-4-5).


The operating switch

 PERFORMANCE ORDER

1. Connect to the contact socket of the switch the battery, a tester and the resistor on 500 ÷ 800 Ohms. Measure current, the switch passed in a diagnostic chain in each of working provisions (see the table).


2. Replace the faulty switch.


The left combined understeering switch

See the Section Removal, check of a state and installation of the combined understeering switches.

Door sensors switches of activation of devices of internal lighting

Sensors switches of lateral doors

 PERFORMANCE ORDER

1. Measure resistance between plugs No. 1 and No. 3 of the sensor switch of each of car doors. At an open door the result of measurement has to make less than 1 Ohm, at closed, - more than 1 megohm.

2. Replace faulty sensors switches.


Back door lock latch sensor switch

 PERFORMANCE ORDER

1. Measure resistance between plugs No. 1 and No. 2 of the sensor switch. At an open door the result of measurement has to make less than 1 Ohm, at closed, - more than 1 megohm.
2. Replace faulty sensors switches.


Sensor switch of a cover of a luggage compartment

 PERFORMANCE ORDER

1. Measure resistance between plugs No. 1 and No. 2 of the sensor switch. At an open cover the result of measurement has to make less than 1 Ohm, at closed, - more than 1 megohm.
2. Replace faulty sensors switches.


Switch of the main saloon lamp

 PERFORMANCE ORDER

1. Measure resistance between plugs of the contact socket in all working provisions of the switch. Compare results of measurement to requirements of the table.


2. Replace the faulty switch.

Switches of the directed saloon lamps

 PERFORMANCE ORDER

Measure resistance between plugs No. 1 and No. 2 of the contact socket of an electrical wiring of the lamp. In the closed position of the switch the result of measurement has to make 18 ± 5.4 Ohms, in opened, - more than 1 megohm.

Switch of a lamp of illumination of a luggage compartment (Legacy Station wagon/Outback model)

 PERFORMANCE ORDER

1. Measure resistance between plugs of the contact socket in all working provisions of the switch. Compare results of measurement to requirements of the table.


2. Replace the faulty switch.

Check of the relay of a horn

 PERFORMANCE ORDER

Connect the battery between plugs No. 4 and No. 3 of the relay and measure resistance between plugs No. 1 and No. 2 of the relay. At the connected food the result of measurement has to make more than 1 megohm, at the disconnected battery, - less than 1 Ohm. Replace the faulty relay.