Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
Specifications
Search of causes of failures of electric equipment
Safety locks - the general information
Chain breakers - the general information
The relay - the general information and check of serviceability of functioning
Details of laying of an onboard electrical wiring
System of additional safety (SRS) - the device and the principle of functioning
Diagnostics of malfunctions of SRS
Removal and installation of the SRS components
Control system of speed (tempostat) - the device and the principle of functioning
Check of serviceability of functioning of components and problem diagnostics of a tempostat
Removal, check of a state and installation of components of a control system of speed
Combination of devices - the general information and the principle of functioning of components
Problem diagnostics of components of a combination of devices
Removal, service and installation of a combination of devices, check of a condition of components
Heating of back glass and rear-view mirrors - the general information, check of serviceability of functioning of components, recovery repair of a thermoelectric heating element
Heating of brushes of screen wipers - the general information, check of serviceability of functioning of components, recovery repair of a thermoelectric heating element
Removal, check of a state and installation of switches of management of functioning of the electric drive of regulators of window regulators
The electric drive of rear-view mirrors - check of serviceability of functioning
Removal check and installation of the switch of management of functioning of the electric drive of external rear-view mirrors
Removal, check of a state and installation of the switch of management of functioning of the electric drive of the top hatch
Removal, check of a state and installation of the combined understeering switches
Check of serviceability of functioning of electric motors of the drive of screen wipers, removal, check and installation of the operating relay of a back screen wiper on the Legacy Station wagon/Outback models
Check of the relay and switches of lighting and alarm devices
Removal and installation of illuminants, replacement of lamps
Removal, check of a state and installation of horns and switch of a horn
Check of a state and replacement of contact group of the switch of ignition
The uniform lock - the device, the principle of functioning, diagnostics of malfunctions
Removal, check of a state and installation of components of the uniform lock
System of an immobilization of the engine - the device, the principle of functioning, diagnostics of malfunctions
Removal and installation of components of system of an immobilization of the engine
Removal and installation of assembly of the radio receiver
Removal and installation of loudspeakers
Check of a state and recovery repair of the window antenna of the radio receiver
Removal, installation and check of a condition of the antenna amplifier of the radio receiver
Removal and installation of the lighter
+ Schemes of electric connections
|
Removal, installation and check of a condition of the antenna amplifier of the radio receiver
Removal and installation
Disconnect a negative wire from the battery.
Sedan models
|
|
|
1. Remove the top section finishing of a back rack (see the Head Kuzov).
2. Disconnect the contact socket and the plug of a plait of an electrical wiring.
|
|
3. Turn out fixing screws and remove assembly of the antenna amplifier. |
4. Installation is made upside-down. |
|
Legacy Station wagon/Outback models
|
|
|
1. Remove the lower section of the panel of a back lateral upholstery of salon (see the Head Kuzov).
2. Disconnect the contact socket and the plug of a plait of an electrical wiring.
|
|
3. Turn out fixing screws and remove assembly of the antenna amplifier. |
4. Installation is made upside-down. |
|
Check
European models
|
|
1. Measure resistance of the antenna amplifier. Compare results of measurement to data of the table.
2. The faulty amplifier replace |
|
Other models
|
|
|
1. Measure resistance of the antenna amplifier. Compare results of measurement to data of the table.
2. The faulty amplifier replace |
|
|
|
