Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car


Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
- Onboard electric equipment
   Specifications
   Search of causes of failures of electric equipment
   Safety locks - the general information
   Chain breakers - the general information
   The relay - the general information and check of serviceability of functioning
   Details of laying of an onboard electrical wiring
   System of additional safety (SRS) - the device and the principle of functioning
   Diagnostics of malfunctions of SRS
   Removal and installation of the SRS components
   Control system of speed (tempostat) - the device and the principle of functioning
   Check of serviceability of functioning of components and problem diagnostics of a tempostat
   Removal, check of a state and installation of components of a control system of speed
   Combination of devices - the general information and the principle of functioning of components
   Problem diagnostics of components of a combination of devices
   Removal, service and installation of a combination of devices, check of a condition of components
   Heating of back glass and rear-view mirrors - the general information, check of serviceability of functioning of components, recovery repair of a thermoelectric heating element
   Heating of brushes of screen wipers - the general information, check of serviceability of functioning of components, recovery repair of a thermoelectric heating element
   Removal, check of a state and installation of switches of management of functioning of the electric drive of regulators of window regulators
   The electric drive of rear-view mirrors - check of serviceability of functioning
   Removal check and installation of the switch of management of functioning of the electric drive of external rear-view mirrors
   Removal, check of a state and installation of the switch of management of functioning of the electric drive of the top hatch
   Removal, check of a state and installation of the combined understeering switches
   Check of serviceability of functioning of electric motors of the drive of screen wipers, removal, check and installation of the operating relay of a back screen wiper on the Legacy Station wagon/Outback models
   Check of the relay and switches of lighting and alarm devices
   Removal and installation of illuminants, replacement of lamps
   Removal, check of a state and installation of horns and switch of a horn
   Check of a state and replacement of contact group of the switch of ignition
   The uniform lock - the device, the principle of functioning, diagnostics of malfunctions
   Removal, check of a state and installation of components of the uniform lock
   System of an immobilization of the engine - the device, the principle of functioning, diagnostics of malfunctions
   Removal and installation of components of system of an immobilization of the engine
   Removal and installation of assembly of the radio receiver
   Removal and installation of loudspeakers
   Check of a state and recovery repair of the window antenna of the radio receiver
   Removal, installation and check of a condition of the antenna amplifier of the radio receiver
   Removal and installation of the lighter
   + Schemes of electric connections



d9f1bda0

Removal, service and installation of a combination of devices, check of a condition of components

Details of installation of elements of finishing of a combination of devices and panel of facing of an instrument guard

And — the Forward cover of the central console
In — Facing of the panel of switches
With — the Fixing screw

D — the Central (console) section of finishing of the dashboard
E — Facing


Design of a combination of devices of usual type (1 of 2)

And — the Back cover
In — the Casing
With — the Window panel
D — the Reflector

E — Protective glass
F — the Latch
G — the Latch


Design of a combination of devices of usual type (2 of 2)

And — Clamps
In — Points of placement of clamps
With — the Printed-circuit board
D — Assembly of a speedometer

E — Assembly of a tachometer
F — the Service opening
G — the Casing


Design of a combination of devices of luminescent type

And — the Back cover
In — the Printed-circuit board
With — the Casing
D — Assembly of a tachometer
E — the Window panel
F — Protective glass
G — the Reflector
N — Assembly of a speedometer
I \CFL electrical wiring plait

J — CFL Inverter
To — the Screw
L — the Latch
M — the Latch
N — Clamps
About — the Service opening
R — the Contact socket


Scheme of an arrangement of lamps of a combination of devices of usual type

1 — the Tachometer and the measuring instrument of temperature of cooling liquid
2 — ABS
3 — VDC
4 — oil Pressure
5 — the Charge
6 — ATF Temperature
7 — MIL
8 — the Driving beam
9 — the Index of the right turn
10 — the Tachometer
11 — the Index of the left turn
12 — the Level of brake liquid / raising of the parking brake

13 — the Speedometer
14 — Functioning of VDC
15 — 4WD LO
16 — FWD
17 — VDC OFF
18 — SRS
19 — the Speedometer and the measuring instrument of a reserve of fuel
20 — the Minimum reserve of fuel
21 — ZhK the display
22 — POWER
23 — HOLD
24 — ZhK the display


Scheme of an arrangement of lamps of a combination of devices of luminescent type

1 — the Ring of the measuring instrument of temperature of cooling liquid
2 — the Ring of a tachometer and the measuring instrument of temperature of cooling liquid
3 — ABS
4 — VDC
5 — oil Pressure
6 — MIL
7 — the Charge
8 — ATF Temperature
9 — Activation of external lighting
10 — a tachometer Ring
11 — the Driving beam
12 — the Index of the right turn
13 — HOLD
14 — ZhK the display
15 — POWER
16 — the Index of the left turn

17 — the Level of brake liquid / raising of the parking brake
18 — a speedometer Ring
19 — Functioning of VDC
20 — SRS
21 — FWD
22 — VDC OFF
23 — the Ring of a speedometer and the measuring instrument of a reserve of fuel
24 — a fuel reserve measuring instrument Ring
25 — the Minimum reserve of fuel
26 — Position of the lever of the AT (P) selector
27 — a speedometer Ring
28 — Position of the lever of the AT (D) selector
29 — a tachometer Ring


Removal

 PERFORMANCE ORDER

1. Disconnect SRS (see the Section System of Additional Safety (SRS) - the device and the principle of functioning).
2. Lower a steering column in extreme lower situation.
3. Disconnecting an electrical wiring, remove a forward cover of the central console and facing of the panel of switches.
4. Turn out fixing screws and remove the central (console) section of finishing of the dashboard facing (peak) of an instrument guard.

5. Turn out fixing screws and remove a combination of devices, disconnect an electrical wiring.


Dismantling

 In order to avoid leaving of fingerprints on glass surfaces of dials of measuring instruments put on gloves!


Combination of usual type

 PERFORMANCE ORDER

1. Release a latch (F) and remove from a back cover (And) a casing (In).
2. Release a latch (G) and remove from an internal casing glass of an instrument guard (E), a reflector (D) and the window panel (C).
3. Flat-nose pliers delay clamps (And) in points (In) the printed-circuit board of a combination and through openings (F) up, wring out outside of assembly of a speedometer (D) and a tachometer (E).
4. Delay a clamp in the center of the printed-circuit board up (C) combinations of devices and remove the printed-circuit board from a casing (G).


Combination of luminescent type

 PERFORMANCE ORDER

1. The design of a combination of devices of luminescent type is presented on an illustration.
2. Turn out the screw (To), disunite contact sockets and remove an inverter (J) of a holodnokatodny fluorescent lamp (CFL).
3. Release a plait (I) electrical wiring of CFL from a flute in a back cover, release a latch (M) and remove from a casing (C) protective glass (F), a reflector (G) and the window panel (E).

4. Uncover the socket, having pulled for both edges, release clamps and disunite sockets of the flexible printed-circuit board of a combination of devices.

5. By means of nippers release clamps (N) on a back cover (And).
6. Through openings (About) push out outside of assembly of a speedometer (N) and a tachometer (D)
7. Release the central clamp and remove the printed-circuit board from a casing.


Replacement of lamps of a combination of devices

The scheme of an arrangement of lamps of a combination of devices is submitted on illustrations.

Assembly

Assembly is made as it should be, the return to an order of dismantle of components.

Installation

Installation is made as it should be, the return to an order of dismantle of components, - track correctness of connection and reliability of fastening of contact sockets of an electrical wiring, make sure of serviceability of functioning of measuring instruments.

Check of a condition of components

Speedometer

 PERFORMANCE ORDER

1. Remove from a combination of devices assembly of a speedometer with the fuel reserve measuring instrument (see above).

2. Measure resistance between SIN plugs (+) - SIN (-) and COS (+) - COS (-) of the contact socket of a speedometer. If the result of measurement exceeds the limit of range 208 ± 8 Ohms, replace assembly of a speedometer with the fuel reserve measuring instrument, otherwise the speedometer in an order and should be replaced the printed-circuit board of a combination of devices.

3. Installation is made upside-down.


Tachometer

 PERFORMANCE ORDER

1. Remove from a combination of devices assembly of a tachometer with the engine temperature measuring instrument (see above).
2. Check is made by analogy with check of a speedometer.
3. Installation is made upside-down.


Fuel reserve measuring instrument

 PERFORMANCE ORDER

1. Remove from a combination of devices assembly of a speedometer with the fuel reserve measuring instrument (see above).
2. Installation is made upside-down.


Engine temperature measuring instrument

 PERFORMANCE ORDER

1. Remove from a combination of devices assembly of a tachometer with the engine temperature measuring instrument (see above).
2. Measure resistance between IGN-GND, IGN-UNIT and UNIT-GND plugs of the contact socket of the measuring instrument. Nominal rates make 208 ± 10 Ohms, 56 ± 10 Ohms and 264 ± 10 Ohms respectively. At negative results of check replace the measuring instrument assembled with a speedometer, otherwise replace the printed-circuit board.
3. Installation is made upside-down.


Sensor of temperature of external air

 PERFORMANCE ORDER

1. Open a cowl.
2. Disconnect a negative wire from the battery.

3. Disconnect an electrical wiring and remove the sensor of temperature of external air from the lower radiator panel.

4. Measure resistance between plugs of the contact socket of the sensor. If at a temperature of 25 °C the result of measurement differs from value of 1.7 kOhm, replace the sensor.