Subaru Legacy/Outback

1. Remove a forward top slip.
2. Remove the top panel of finishing of a forward rack.
3. Remove an anchor of humeral section of a forward seat belt, then release clamps and remove the top panel of finishing of the central rack.

4. Installation is made upside-down, - track correctness of input of the top slip in gearing with the top panels of finishing of forward and central racks. Make sure of reliability of a zashchelkivaniye of clamps.

1. Remove a back top slip.

2. Turn out fixing bolts and remove a stoplight of the top level.

3. Remove a back of a back seat (see the Section Removal, service and installation of seats).

4. Remove the anchor section of the right seat belt equipped with a buckle and disconnect it from humeral section of the central belt.

5. Through grooves and the central window in the finishing panel of the back shelf release humeral sections of seat belts, then release clamps and remove the panel.

6. Remove the top cover of an overlay of a threshold of a back door (see below).
7. Remove the lower panel of finishing of a back rack.
8. Remove the top panel of finishing of a back rack.

1. Remove the top cover of an overlay of a threshold of a back door (see below).
2. Remove the panel of finishing of a back skirt.
3. Turn out fixing screws, release clamps and remove the main section of the back lateral panel of finishing.
4. Remove a back top slip.
5. Turn out fixing screws and remove the top section of the back lateral panel of finishing.
6. Remove the top cross panel of finishing.

Installation is made upside-down, - track correctness of input of the top slip in gearing with the top panel of finishing of a back rack / the top section of the panel of back lateral finishing. Make sure of reliability of a zashchelkivaniye of clamps.

1. Remove the lower panel of finishing of a forward rack.
2. Remove the lower cover of an overlay of a threshold of a forward door.
3. Remove (Sedan models) / lift (Legacy Station wagon/Outback models) a pillow of a back seat (see the Section Removal, service and installation of seats), then remove the top cover of an overlay of a threshold of a back door.
4. Remove the lower cover of an overlay of a threshold of a back door.
5. Remove the lower panel of finishing of the central rack.
6. Installation is made upside-down, - track reliability of a zashchelkivaniye of clamps.

2. Installation is made upside-down.

1. Disconnect a negative wire from the battery.
2. Remove the switch of management of functioning of the electric drive of the top hatch (see the Head Onboard electric equipment).
3. Remove the ceiling lamp (see the Head Onboard electric equipment).
4. Remove sun-protection peaks and their loopy hooks (see above).

5. Turn out fixing bolts and remove the top hand-rail.

6. Remove lateral elements of finishing of the top level of forward and back parts of salon (see above).

Need for removal of finishing of the back shelf in this case, naturally, no.

7. Take fixing clamps and remove the panel of a ceiling upholstery.

2. Disconnect a negative wire from the battery.
3. At the corresponding complete set of the car remove the switch of management of functioning of the electric drive of the top hatch (see the Head Onboard electric equipment).
4. Remove the main ceiling lamp and a lamp of illumination of a luggage compartment (see the Head Onboard electric equipment).
5. Remove sun-protection peaks and their loopy hooks (see above).
6. Turn out fixing bolts and remove the top hand-rail.
7. Remove lateral elements of finishing of the top level of forward and back parts of salon (see above).

8. Having accurately released the clamp lock, uncover and, having pushed in a pocket in a ceiling upholstery, release the main section of the central seat belt of a back seat equipped with a castle bracket from the opposite side. And — the Cover In — the Seat belt

9. Take fixing clamps and remove the panel of a ceiling upholstery.

Installation is made as it should be, the return to an order of dismantle of components, - track reliability of a zashchelkivaniye of clamps.

1. Release fixing clamps and remove the back panel of finishing of a luggage compartment.
2. Having turned out the fixing screw, remove an angular hook, inventions release clamps and remove the lateral panel of finishing of a luggage compartment.
3. Installation is made upside-down, - track reliability of a zashchelkivaniye of clamps.

1. Remove forward seats (see the Section Removal, service and installation of seats).
2. Remove a pillow of a back seat (see the Section Removal, service and installation of seats).
3. Remove a console box (see the Section Removal and installation of elements of the central console).
4. Remove elements of finishing of the lower level of salon (see above).

5. Take plastic clamps of fastening of the carpet panel of a covering of a floor.

6. Remove the fixing hook and unbend forward edges of the carpet panel in foot wells of the driver and forward passenger.
7. Remove the carpet panel from a sleeve of supply of hot air in back part of salon.
8. Curtail the carpet panel and take it from salon of the car. Through a back door.
9. Installation is made upside-down, - track reliability of a zashchelkivaniye of clamps, do not forget to fill side edges of the carpet panel in reception grooves in covers of overlays of door thresholds.

1. Open a cover of a luggage compartment.

2. Simply lift the carpet panel and remove it from the car.

3. Installation is made upside-down.

2. Take forward clamps and remove panels and remove forward section of the carpet panel.
3. Installation is made upside-down, - track reliability of a zashchelkivaniye of clamps.