Subaru Legacy/Outback

1. Disconnect a negative wire from the battery and before starting removal of a seat, wait for not less than 20 seconds necessary for a discharge of the condenser of the independent SRS power supply.

2. Having wrung out the clamp button, remove a head restraint.

3. Incline a back forward.

4. Remove decorative covers of bolts of fastening from a lobby and the back party of poloz of the directing sled.

5. At the corresponding complete set disunite the yellow socket of the electrical wiring of a lateral safety cushion laid under a seat, also disconnect an electrical wiring of a thermoelectric element of heating of a seat and the sensor switch of a control lamp "Fasten belts".

6. Turn out two back bolts of fastening of the directing sled.

7. Shift a seat against the stop back and turn out two forward bolts of fastening of the directing.

8. Lift a seat and take it from salon of the car, - try not to scratch a paint and varnish covering of body panels and not to tear a seat upholstery.

1. Disconnect a negative wire from the battery and before continuing procedure performance, wait for not less than 20 seconds necessary for a discharge of the condenser of the independent SRS power supply.

2. Raise a seat and disunite the yellow socket of the electrical wiring of a lateral safety cushion laid under a seat, also disconnect an electrical wiring of a thermoelectric element of heating of a seat and the sensor switch of a control lamp "Fasten belts".

3. Accurately take a seat from salon of the car, - try not to scratch a paint and varnish covering of body panels and not to tear a seat upholstery.

10. Remove an upholstery.
11. Remove a seat back podbivka.

12. At the corresponding complete set of the car release a plait of an electrical wiring of a lateral safety cushion from intermediate clamps.

13. Give two nuts equipped with protective caps and remove the module of a lateral safety cushion (at the corresponding complete set of the car).

14. On seats with unregulated pillows remove the handle of the lever of adjustment of an inclination of a back and a lateral overlay of loopy assembly.

15. On models with adjustable pillows turn out four loopy bolts and remove a seat pillow.

16. On models with unregulated pillows of seats turn out lateral bolts of fastening of a pillow and remove the last from a frame.

17. Release spring clamps from the lower party of a pillow of a seat and remove wire rings.

18. At the corresponding complete set of the car release an electrical wiring of a thermoelectric element of heating of a pillow from intermediate clamps.

19. Remove spring rings of fastening of an upholstery.

20. Remove an upholstery and a podbivka of a pillow of a seat.

21. On models with adjustable pillows of a seat release spring clamps and remove handles of adjustment of height of provision of a pillow of a seat.

22. On models with adjustable pillows of a seat remove the handle of the lever of adjustment of an inclination of a back of a seat.

23. On models with adjustable pillows turn out fixing bolts (previously remove decorative covers) and remove a lateral overlay of loopy assembly.

24. On models with adjustable pillows remove a podbivka of a pillow and a decorative overlay of a loopy spring.

25. On models with adjustable pillows turn out four fixing bolts and remove runners of a sled of a seat.

26. On models with unregulated pillows of seats turn out four fixing screws and remove loopy assemblies.

27. On models with unregulated pillows turn out four fixing bolts and remove runners of a sled.

28. Remove a connecting electrical wiring.

1. Release spring clamps from the lower party of a pillow of a seat and remove wire rings.
2. At the corresponding complete set of the car release an electrical wiring of a thermoelectric element of heating of a pillow from intermediate clamps.
3. Remove spring rings of fastening of an upholstery, - the scheme of an arrangement of rings on pillows of electrodriving rings is identical to pillows with a fabric and leather upholstery.
4. Remove an upholstery and a podbivka of a pillow of a seat.

5. Turn out the fixing screw and remove a back slip.

6. On seats with the 8-position drive turn out the fixing screw and disconnect an electrical wiring from assembly of the switch in the lower part of an overlay of loopy assembly, then remove a slip.

7. On seats with the 6-position drive remove the handle of the lever of adjustment of an inclination of a back of a seat.

8. Remove the slip established from the back party of a loop then turn out two fixing bolts and remove loopy assembly.

1. Assembly is carried out as it should be, the return to an order of dismantle of components, - try not to soil an upholstery and track smoothness of its landing.
2. On seats with the manual drive and an unregulated pillow track that the internal loop correctly got to an upholstery window.
3. Make sure of correctness of connection and reliability of fixing of contact sockets of an electrical wiring, track that plaits were not jammed.
4. Tighten all fixture with the demanded effort (see Specifications).

2. With the demanded effort (53 Nanometers) tighten four bolts of fastening of a sled.
3. Check serviceability of functioning of the mechanism of adjustment of provision of a seat.

3. Having lifted a back, take it from salon of the car.

6. Having pulled up, release head restraints from both sections of a back.

7. Take clamps and remove forward section of the back carpet panel of a covering of a floor.

8. Having inclined both sections of a back, give loopy bolts / nuts.

9. Remove assembly of a back.

1. Release the spring rings located on perimeter of a seat back of the back party.

2. At the corresponding complete set give two fixing nuts and remove the central armrest.

3. Having dismantled spring rings, remove a back upholstery.

4. Release the spring rings located on perimeter of a seat pillow of the lower party.

5. Having dismantled spring rings, remove a pillow upholstery.

3. Rotating counterclockwise, remove the back handle.

4. Having grasped a mouthpiece nippers, remove the plug of fixing of the directing head restraint probe.

5. Remove a hook of fixing of a back.

6. Having released the fixing tape, remove a back upholstery of a back.

7. Remove the lower hook.

8. Release on four clamps.

9. Remove eight spring rings.

10. Remove four forward spring rings from a back podbivka.

11. Remove a back upholstery.

12. Turn out fixing bolts and remove loopy levels of a pillow of a seat.

13. Remove facing of a belt loop.

14. Take clamps and remove the lower upholstery of a pillow.

15. Having dismantled a hook, remove a frame.

16. Having dismantled spring rings, remove an upholstery.

Assembly is carried out as it should be, the return to an order of dismantle of components, - try not to soil an upholstery and track smoothness of its landing.

1. Installation is made as it should be, the return to an order of dismantle of components.

2. At installation of a back of a seat on the Sedan models at first put her on the top hooks and later tighten the lower fixing bolts.

3. Track that all fixture was tightened with the demanded effort.