Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car

Removal, service and installation of screen wipers and components of a path of supply of the washing liquid

Design of forward screen wipers


1 — Rubber working elements 2 — Brushes 3 — Levers (leads) 4 — Drafts 5 — the Driving electric motor	Efforts of a tightening of threaded connections, Nanometer T1: 6.0 T2: 20

Design of forward screen wipers


1 — the Rubber working element 2 — the Brush 3 — the Lever (lead) 4 — the Driving electric motor 5 — the Remote washer And 6 — the Pillow 7 — the Remote washer In 8 — the Nut 9 — the Cover	10 — the Overlay of the lever Efforts of a tightening of threaded connections, Nanometer T1: 5.9 T2: 7.4 T3: 7.8

The scheme of the organization of supply of the washing liquid on wind and back flew down the car


1 — Nozzles of supply of the washing liquid 2 — Connecting hoses 3 — the Tank 4 — the Cover 5 — the Pump of supply of the washing liquid on a windshield 6 — the Pump of supply of the washing liquid on back glass	7 — the Sealing landing plug Efforts of a tightening of threaded connections, Nanometer Т: 6.0

The combined understeering switch of management of functioning of screen wipers

See the Head Onboard electric equipment.

Forward screen wipers

Replacement of brushes

PERFORMANCE ORDER

1. Take away the screen wiper lever from a windshield.

2. Having wrung out a lock uvula, remove a brush from the lever.

3. Having delayed outside a clamp, take a rubber working element from a brush frame.

4. Fill a new working element in a brush, - track that the clamp appeared from the party of a brush turned towards the lever. Make sure of reliability of a zashchelkivaniye of a clamp.

Removal, installation and adjustment of levers

PERFORMANCE ORDER

1. Open a cowl.
2. Remove protective caps of fixing nuts.

3. Release nuts and remove levers.

4. Installation is made upside-down. Having finished installation, once activate screen wipers, then level levers so that average points of brushes appeared directly over ceramic adjusting tags on the windshield panel.

Removal and installation of components of the drive of screen wipers

PERFORMANCE ORDER

The description of procedure of check of serviceability of functioning of a driving electric motor is provided in the Section Check of Serviceability of Functioning of Electric Motors of the Drive of Screen Wipers, removal, check and installation of the operating relay of a back screen wiper on the Legacy Station wagon/Outback models of the Head Onboard electric equipment.

1. Remove the panel of a forward fairing (see the Section Removal and installation of a forward fairing).
2. Disconnect an electrical wiring from a driving electric motor.

3. Release fixing bolts and nuts and remove assembly of the drive of screen wipers.

4. In case of need give fixing bolts and nuts and remove a driving electric motor from assembly.

5. Installation is made upside-down.

Back screen wiper (Legacy Station wagon/Outback models)

PERFORMANCE ORDER

The description of procedures of removal/installation and check of a condition of the operating relay is provided in the Section Check of Serviceability of Functioning of Electric Motors of the Drive of Screen Wipers, removal, check and installation of the operating relay of a back screen wiper on the Legacy Station wagon/Outback models of the Head Onboard electric equipment.

Details of a design of screen wipers are shown on an illustration.

Removal, installation and adjustment of the lever

PERFORMANCE ORDER

1. Cast away an overlay of the lever, release a fixing nut and remove the lever.

2. Installation is made upside-down. Having finished installation, once activate a screen wiper, then level it so that the brush appeared the conducting thread of a thermoelectric element of heating of back glass located in parallel.

Removal and installation of a driving electric motor

PERFORMANCE ORDER

1. Remove the screen wiper lever (see above).
2. Remove a protective cover, a fixing nut, remote washers and a rubber pillow.
3. Remove the lower panel of internal finishing of a door of a back (see the Section Removal and installation of panels of an internal upholstery of doors, including a back door (the Station wagon models Legacy and Outback) and a cover of a luggage compartment (Sedan model)).
4. Release an electrical wiring plait clamp, then disunite the contact socket of a driving electric motor.

5. Turn out fixing bolts and remove assembly of a driving electric motor.

6. Installation is made upside-down, - track that the rubber pillow was developed by a tag in the form of an arrow up.

Components of a path of supply of the washing liquid

The scheme of the organization of supply of the washing liquid on wind and back glasses of the car is submitted on an illustration.

Removal, installation and adjustment snuffled supply of the washing liquid

Windshield nozzles

PERFORMANCE ORDER

1. Open a cowl and disconnect a hose of supply of the washing liquid from reception unions of the nozzle which is subject to replacement.

2. A screw-driver, or other suitable tool wring out lock uvulas and release a nozzle from the cowl panel.

3. Installation is made upside-down, - track that the hose of supply of the washing liquid was not overwound.

4. Adjust nozzles according to the scheme provided on an illustration.

А: 350 mm
В: 150 mm
С: 300 mm
D: 600 mm

Nozzle of back glass (Legacy Station wagon/Outback model)

PERFORMANCE ORDER

1. Remove a stoplight of the top level (see the Head Onboard electric equipment).
2. Disconnect a hose of supply of the washing liquid from the reception union of a nozzle.
3. A screw-driver, or other suitable tool wring out lock uvulas and release a nozzle from the back door panel.
4. Installation is made upside-down, - track that the hose of supply of the washing liquid was not overwound.

5. Adjust a nozzle according to the scheme provided on an illustration.

А: 60 mm
В: 42 °

Removal and installation of the tank and pump(s) of supply of the washing liquid

PERFORMANCE ORDER

1. Open a cowl.

2. Turn out two fixing bolts, disconnect a hose(s) and the contact socket(s) of an electrical wiring of the pump(s) of supply of the washing liquid.

3. Remove the tank.

4. Release the suspect (or needing replacement) the pump from the landing plug in the tank case.

5. Having given on pump plugs tension from the battery, make sure of serviceability of rotation of an electric motor.
6. Installation is made as it should be, the return to an order of dismantle of components.