Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
- Body
   Specifications
   Service of loops and locks of the car
   Replacement wind and the other fixed glasses
   Removal and installation of a decorative front grille
   Removal and installation of the panel of protection of a case
   Removal and installation of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of loker of protection of arches of forward wheels
   Removal and installation of lateral overlays of body panels
   Removal and installation of a forward fairing
   Removal and installation of a back spoiler
   Removal and installation of lateral spoilers
   Removal and installation profile directing the top luggage carrier
   Removal installation of the main ware box
   Removal and installation of elements of the central console
   Removal and installation of the dashboard
   Removal and installation of panels of an internal upholstery of doors, including a back door (the Station wagon models Legacy and Outback) and a cover of a luggage compartment (Sedan model)
   Removal and installation of elements of internal finishing
   Seat belts - the general information, check of a state, removal and installation, an order of utilization of not worked emergency natyazhitel
   Removal, service and installation of seats
   Removal, installation and adjustment of a cowl
   Removal, installation and adjustment of the lock of a cowl
   Removal and installation of forward wings
   Removal, installation and adjustment of door panels
   Removal, service and installation of components of the top hatches
   Removal, installation and check of components of castle assemblies
   Removal, installation and adjustment of door glasses and components of window regulators
   Removal, service and installation of rear-view mirrors
   Removal, service and installation of screen wipers and components of a path of supply of the washing liquid
   Control body sizes
+ Onboard electric equipment









d9f1bda0


Removal, service and installation of rear-view mirrors

 The description of procedures of removal and installation of switches of management of functioning of the electric drive of door mirrors is provided in the Head Onboard electric equipment.


Internal mirror

Removal and installation

 PERFORMANCE ORDER

1. Develop a mirror support under 90 ° in any direction and, having pulled down, remove it from the basis pasted on glass.

2. Take a spring from assembly of the basis of a support of a mirror.

3. Check a condition of glass and a spring of the basis, replace defective components.
4. Installation is made upside-down.


External mirrors

Removal and installation


 PERFORMANCE ORDER

1. Remove the panel of an internal upholstery of a door (see the Section Removal and installation of panels of an internal upholstery of doors, including a back door (the Station wagon models Legacy and Outback) and a cover of a luggage compartment (Sedan model)).

2. Unbend a corner of an insulating slip and disunite the contact socket of an electrical wiring of a mirror.

3. Turn out fixing screws and remove assembly of a mirror from a door.

4. Installation is made upside-down.


Replacement flew down

 PERFORMANCE ORDER

1. Remove assembly of a mirror from a door (see above).

2. Warm up the hair dryer the holder to a softening of its edges, when using the hair dryer with a power of 1 kW the sufficient warming up of the holder occurs already two-three minutes later.

3. Hooking a stupid screw-driver, separate glass from the holder. On models with heating of mirrors disconnect an electrical wiring of a thermoelectric heating element from the back party of glass.
4. Again warm up the holder's surface the hair dryer, remove a film from a bilateral adhesive tape of fastening of glass and densely press the last to the holder.

 Refusal of preliminary warming up of the holder is interfaced to risk damage of its edges, or mirror glass splitting!

5. Establish assembly of a mirror the regular place (see above).