Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
- Body
   Specifications
   Service of loops and locks of the car
   Replacement wind and the other fixed glasses
   Removal and installation of a decorative front grille
   Removal and installation of the panel of protection of a case
   Removal and installation of a front bumper
   Removal and installation of a rear bumper
   Removal and installation of loker of protection of arches of forward wheels
   Removal and installation of lateral overlays of body panels
   Removal and installation of a forward fairing
   Removal and installation of a back spoiler
   Removal and installation of lateral spoilers
   Removal and installation profile directing the top luggage carrier
   Removal installation of the main ware box
   Removal and installation of elements of the central console
   Removal and installation of the dashboard
   Removal and installation of panels of an internal upholstery of doors, including a back door (the Station wagon models Legacy and Outback) and a cover of a luggage compartment (Sedan model)
   Removal and installation of elements of internal finishing
   Seat belts - the general information, check of a state, removal and installation, an order of utilization of not worked emergency natyazhitel
   Removal, service and installation of seats
   Removal, installation and adjustment of a cowl
   Removal, installation and adjustment of the lock of a cowl
   Removal and installation of forward wings
   Removal, installation and adjustment of door panels
   Removal, service and installation of components of the top hatches
   Removal, installation and check of components of castle assemblies
   Removal, installation and adjustment of door glasses and components of window regulators
   Removal, service and installation of rear-view mirrors
   Removal, service and installation of screen wipers and components of a path of supply of the washing liquid
   Control body sizes
+ Onboard electric equipment









d9f1bda0


Removal and installation of lateral overlays of body panels

Details of installation of lateral slips

1 — the Forward slip
2 — the Back slip
3 — the Overlay of a forward wheel arch
4 — the Overlay of a forward door

5 — the Overlay of a back door
6 — the Overlay of an arch of a back wheel arch
7 — the Overlay of door thresholds


Pay attention much arrangements and a design of the clamps used for fastening of lateral slips.

 

 

REMOVAL

 PERFORMANCE ORDER

1. Paste over a slip on perimeter with an adhesive tape.

 If the slip is established into place, stick it with an adhesive tape entirely.

2. Get a scaffold with a diameter of 0.8 mm under face edge of a slip and, having pulled for it, cut a sticky layer of a bilateral adhesive tape by means of which the slip fastens to the body panel.

3. Carefully delaying on itself edge of a slip, by means of a special stripper release fixing clamps.

 For the purpose of increase of efficiency of action of structure for removal of sticky weight, do not tear off fragments of a bilateral adhesive tape from the body panel and the back party of a slip.

4. If for fastening of a slip the bilateral adhesive tape of considerable thickness was used, remove part of a layer, having cut it with a knife with a thin flexible edge.
5. Moisten adhesive tape fragments with structure like Sumitomo 3M4000.

 Try not to allow hits of structure on a surface of a paint and varnish covering of a body element!

6. Cover the moistened adhesive tape with a polyethylene film and within 5-10 minutes warm up a lamp of infrared radiation, - the surface under a film should be warmed up to the temperature about 40 ÷ 60 °C.

 Do not allow the overheat of a film leading to its zamutneniye!

7. Accurately remove with the plastic pallet fragments of a bilateral adhesive tape from a surface of the body panel.
8. Unstick a protective adhesive tape and finally clear a door surface of glue traces, having wiped its pure rags moistened with gasoline.
9. In case of need, working similarly, remove a fragment of a bilateral adhesive tape from the back party of a slip.

INSTALLATION

 PERFORMANCE ORDER

1. If the slip which was in the use is established, miss the mark its back party with a Sumitomo 3MK-500 primer and, after drying of the last, paste on it strips of a bilateral adhesive tape (Sumitomo 3M5306 type) 1.2 mm thick and 5 mm wide.

2. By means of a lamp of IK-radiation warm up the body panel and the back party of a slip up to the temperature of 40 ÷ 60 °C.
3. Remove a protective film / paper from a surface of a bilateral adhesive tape and, passing clamps throughout reception openings in the body panel, press a slip to a surface of the last, at the same time latching clamps. Prokatayte a slip a roller with clamping effort not less than 5 kgfs, try not to allow hits under an overlay of air. Make sure of reliability of a zashchelkivaniye of clamps.
4. For the purpose of providing a guarantee of reliable polymerization of adhesion do not wash the car within at least 24 hours.