Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car


Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
- Engine
   Specifications
   Check of compression pressure in cylinders and tightness of the block
   Diagnostics of a condition of the engine with use of the vacuum gage
   The engine lubrication system - the general information
   + the repair Procedures which are not connected with extraction of the engine from the car - four-cylinder engines
   - The repair procedures which are not connected with extraction of the engine from the car - six-cylinder engines
      Reduction of the piston of the first cylinder in situation VMT
      Check and adjustment of valvate gaps
      Removal and installation of a pulley of a cranked shaft
      Removal and installation of covers of the GRM drive
      Removal and installation of gas-distributing chains
      Removal and installation of asterisks of the drive of camshafts
      Removal and installation of an asterisk of a cranked shaft
      Automatic natyazhitel of a gas-distributing chain - the general information
      Removal and installation of camshafts
      Removal and installation of heads of cylinders
      Removal and installation of the lower section of the pallet of a case and maslozabornik
      Removal, service and installation of the oil pump
      Service of the reducing valve of the oil pump
      Check of pressure of motive oil
      Removal and installation of the sensor switch of pressure of oil
      Removal and installation of the oil cooler
      Removal and installation of a driving disk
      Replacement of support of a suspension bracket of the power unit
   + General and capital repairs of engines
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



d9f1bda0

Check and adjustment of valvate gaps

CHECK

See the Head Routine maintenance.

ADJUSTMENT

 PERFORMANCE ORDER

 Adjustment of valvate gaps has to be carried out on the cold engine.


1. By means of the special ST 18252AA000 tool turn a cranked shaft in the direction clockwise, achieving that the subject drive cam to valve check was developed by a working ledge under 90 ° to a face surface of a pusher.
2. By means of the probe of lezviyny type measure the size of a valvate gap. Compare results of measurements to requirements of Specifications. In case of need make necessary adjustments (see further).
3. Remove an adjusting washer from a pusher of the corresponding valve.

4. Prepare the special adaptation for replacement of adjusting washers (ST 18329AA000).

5. Develop pushers selections under 45 °.

6. Having achieved combination of the correct combination with selection, install the ST 18329AA000 adaptation on a valve pusher.

 Track that the edge of the adaptation did not concern an adjusting washer.

7. Tighten bolts (A) and (In) adaptations.

8. Having filled tweezers in selection in a pusher, take an adjusting washer.

 Alternatively the washer can be taken by means of a magnet that in an essential measure reduces probability of falling of a washer.

9. Measure by a micrometer thickness of the removed washer.
10. Based on result of the last measurement and data on the size of a valvate gap obtained earlier, make selection of a new washer (see the table given below), - be guided by the following formulas:

· For inlet valves: S = (V + T) – 0.20 (mm)
· For final valves: S = (V + T) – 0.25 (mm)
Where: S - thickness of the used washer, V – the measured valvate gap, T – the demanded washer thickness.
11. Establish the chosen washer on a pusher.
12. Once again measure gap size, in case of need repeat adjustment.
13. Working in a similar manner, adjust gaps of all valves.

 Turn a cranked shaft only in the direction clockwise!

14. Having finished adjustment, establish the removed components as it should be, the return to an order of their dismantle.

The list of the let-out adjusting washers

detail No.
Thickness, mm
13218AK010
2.00
13218AK020
2.02
13218AK030
2.04
13218AK040
2.06
13218AK050
2.08
13218AK060
2.10 
13218AK070
2.12
13218AK080
2.14
13218AK090
2.16
13218AK100
2.18
13218AK110
2.20
13218AE710
2.22
13218AE720
2.23
13218AE730
2.24
13218AE740
2.25
13218AE750
2.26
13218AE760
2.27
13218AE770
2.28
13218AE780
2.29
13218AE790
2.30
13218AE800
2.31
13218AE810
2.32
13218AE820
2.33
13218AE830
2.34
13218AE840
2.35
13218AE850
2.36
13218AE860
2.37
13218AE870
2.38
13218AE880
2.39
13218AE890
2.40
13218AE900
2.41
13218AE910
2.42
13218AE920
2.43
13218AE930
2.44
13218AE940
2.45
13218AE950
2.46
13218AE960
2.47
13218AE970
2.48
13218AE980
2.49
13218AE990
2.50
13218AF000
2.51
13218AF010
2.52
13218AF020
2.53
13218AF030
2.54
13218AF040
2.55
13218AF050
2.56
13218AF060
2.57
13218AF070
2.58
13218AF090
2.60
13218AF100
2.61
13218AF110
2.62
13218AF120
2.63
13218AF130
2.64
13218AF140
2.65
13218AF150
2.66
13218AF160
2.67
13218AF170
2.68
13218AF180
2.69
13218AF190
2.70
13218AF200
2.71
13218AF210
2.72
13218AF220
2.73
13218AF230
2.74
13218AF240
2.75
13218AF250
2.76
13218AF260
2.77
13218AF270
2.78
13218AF280
2.79
13218AF290
2.80
13218AF300
2.81