Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
- Engine
   Specifications
   Check of compression pressure in cylinders and tightness of the block
   Diagnostics of a condition of the engine with use of the vacuum gage
   The engine lubrication system - the general information
   - The repair procedures which are not connected with extraction of the engine from the car - four-cylinder engines
      Reduction of the piston of the first cylinder in situation VMT
      Check and adjustment of valvate gaps
      Removal and installation of a pulley of a cranked shaft
      Removal and installation of forward covers of the GRM drive
      Removal and installation of a belt of the GRM drive, check of a condition of components
      Removal, check of a state and installation of cogwheels of camshafts
      Removal and installation of a cogwheel of a cranked shaft
      Natyazhitel of a gas-distributing belt - the general information and the principle of functioning
      Removal, check of a state and installation of elements of the drive of valves
      Removal and installation of camshafts
      Removal and installation of heads of cylinders
      Removal and installation of the pallet of a case and maslozabornik
      Removal, service and installation of the oil pump
      Check of pressure of motive oil
      Removal and installation of the sensor switch of pressure of oil
      Removal, check of a state and installation of a flywheel / driving disk
      Replacement of support of a suspension bracket of the power unit
   + the repair Procedures which are not connected with extraction of the engine from the car - six-cylinder engines
   + General and capital repairs of engines
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




d9f1bda0



Removal and installation of a pulley of a cranked shaft

REMOVAL

 PERFORMANCE ORDER

1. Take off a V-shaped driving belt (see the Head Routine maintenance).
2. Turn out a bolt of a pulley of a cranked shaft, - blocking of a cranked shaft from a provorachivaniye is made by means of the special tool (ST 499977300 - model of 2.0 l or ST 499977100 - model of 2.5 l).

3. Remove a pulley of a cranked shaft.

INSTALLATION

 PERFORMANCE ORDER

1. Establish a pulley of a cranked shaft on the regular place.
2. Blow air a carving opening under a pulley bolt.
3. Grease carving part and a persistent surface of a bolt of a pulley of a cranked shaft with motive oil.
4. Temporarily tighten bolts with effort of 44 Nanometers
5. On models of 2.0 l block a shaft from a provorachivaniye special the ST 499977300 tool and wrap a bolt of a pulley of a cranked shaft with the demanded effort (127 Nanometers: models of 2.0 l / 177 Nanometer: models of 2.5 l). For keeping of a cranked shaft use the special tool.
6. Make sure that the corner of an inhaling of a bolt of a pulley of a cranked shaft makes not less than 45 ° (models of 2.0 l)/65 ° (models of 2.5 l).

 If the corner of an inhaling of a bolt of a pulley of a cranked shaft makes less stipulated value, the bolt can be damaged! In case of need make replacement of a bolt, - as replaceable it is necessary to use a bolt No. 12369AA011.

7. The order of a tightening of a replaceable bolt is made in the manner similar described above for the bolt which was in the use (the corner of a tightening has to lie in the range of 40 ÷ 60 °/65 ÷ 75 ° respectively – the goniometric scale is applied on a belt cover).

8. Establish a natyazhitel of a belt of the drive of the К/В compressor.

9. Establish a driving belt and make adjustment of its tension (see the Head Routine maintenance).