Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
- Automatic transmission
   Specifications
   Electrohydraulic control system - the general information, purpose of basic elements
   System of self-diagnostics - the general information and the principles of functioning
   Diagnostics of the general condition of AT
   Problem diagnostics of AT
   Removal and installation of transmission assembly
   Replacement of elements of a suspension bracket of transmission assembly
   Replacement of an epiploon of a casing of lengthening of AT
   Check of a state, adjustment and replacement of the sensor switch of permission of start
   Removal and installation of the forward sensor of the speed (VSS)
   Removal and installation of the back sensor of the speed (VSS)
   Removal and installation of the sensor of turns of the turbine of the hydrotransformer
   Removal, service and installation of valvate assembly
   Replacement of electromagnetic valves of switching, executive electromagnetic valves and sensor of temperature of ATF
   Replacement of the ATF filter
   Removal and installation of the module of management of transmission (TCM)
   Removal, installation and check of a condition of lines of a path of cooling of ATF
   Removal, service and installation of components of the lever of the AT selector
   Removal, installation, check of a state and adjustment of a driving cable of the AT selector
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




d9f1bda0

Check of a state, adjustment and replacement of the sensor switch of permission of start

CHECK

 PERFORMANCE ORDER

1. At violations of serviceability of functioning of a starter and errors of switchings of AT first of all check quality of the drive of gear shifting. In the absence of visible malfunctions check the sensor switch of permission of start.
2. Disunite the contact socket of an electrical wiring of the sensor switch.
3. Check conductivity of electric contours of the sensor switch of permission of start in each of provisions of the lever of the selector.

 Also make sure of lack of conductivity of a chain of ignition in all provisions of the lever of the selector, except provisions "P" and "N".


4. At violations of serviceability of functioning of the sensor switch estimate quality of contact connections of plugs of its socket on the party of transmission, - the functional purpose of plugs is explained in the table given below.

Quality check of contact in the socket of the sensor switch of permission of start


5. Check existence of conductivity in symmetric points at a selector lever deviation on 1.5 ° in both directions from the situation "N". With conductivity in one point and absence it in another, and also in case of violation of symmetry adjust the sensor switch.

A — Is not present conductivity
B — Conductivity is
With — 1.5 °

6. Repeat the checks described above. At detection of deviations adjust a driving cable of the selector.

ADJUSTMENT

 PERFORMANCE ORDER

1. Transfer the selector lever to the situation "N".
2. Weaken three bolts of fastening of the sensor switch of permission of start.

3. Insert a blocking pin of ST 499267300 as it is possible in more vertical situation in openings in the lever and in the case of the sensor switch of permission of start.

4. Tighten fixing bolts with the demanded effort (3.5 Nanometers).
5. Repeat the checks described in the previous subsection. If during these checks malfunction of the sensor switch of permission of start is found, replace it.

Removal and installation

 PERFORMANCE ORDER

1. Tire out the car on the elevator.
2. Transfer the selector lever to the situation "N".
3. Remove the air cleaner or the air inlet camera.

4. Disunite the contact socket of the sensor switch of permission of start and release it from a basic arm.

A Sensor switch of permission of start

5. Lift the car.
6. Remove reception and central sections of an exhaust pipe.

7. Take the forelock from the executive lever of a choice of ranges.

A — the Executive lever of a choice of ranges
In — the Forelock
With — a selector Cable
D — the Clamp
E — the Washer

8. Remove assembly of a plate from a transmission case.

A — a selector Cable
B — Assembly of a plate

9. Turn out fixing bolts.
10. Having shifted the executive lever of a choice of ranges to the left, transfer it to parking situation. Remove the sensor switch of permission of start.
11. Disconnect an electrical wiring from the sensor switch.
12. Installation is made upside-down. Track that all fixture was tightened with the demanded effort (3.5 Nanometers: for bolts of fastening of the sensor switch and 24.5 Nanometers: for bolts of fastening of assembly of a plate), - at a tightening of bolts of fastening of the sensor switch of permission of start use a blocking pin of ST 499267300.