Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
- Automatic transmission
   Specifications
   Electrohydraulic control system - the general information, purpose of basic elements
   System of self-diagnostics - the general information and the principles of functioning
   Diagnostics of the general condition of AT
   Problem diagnostics of AT
   Removal and installation of transmission assembly
   Replacement of elements of a suspension bracket of transmission assembly
   Replacement of an epiploon of a casing of lengthening of AT
   Check of a state, adjustment and replacement of the sensor switch of permission of start
   Removal and installation of the forward sensor of the speed (VSS)
   Removal and installation of the back sensor of the speed (VSS)
   Removal and installation of the sensor of turns of the turbine of the hydrotransformer
   Removal, service and installation of valvate assembly
   Replacement of electromagnetic valves of switching, executive electromagnetic valves and sensor of temperature of ATF
   Replacement of the ATF filter
   Removal and installation of the module of management of transmission (TCM)
   Removal, installation and check of a condition of lines of a path of cooling of ATF
   Removal, service and installation of components of the lever of the AT selector
   Removal, installation, check of a state and adjustment of a driving cable of the AT selector
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




d9f1bda0



Replacement of electromagnetic valves of switching, executive electromagnetic valves and sensor of temperature of ATF

 PERFORMANCE ORDER

1. The car also establish to Poddomkratta it on props.
2. Clear transmission outside.
3. Turn out a drain stopper and merge ATF then screw a stopper with the demanded effort.
4. Remove the case pallet. Take and carefully clear a magnet. Remove traces of material of old laying from the interfaced surfaces of the pallet and a case of transmission.
5. Disunite contact sockets of executive electromagnetic valves and the socket of the sensor of temperature of ATF. Release sockets from clamps.
6. Remove electromagnetic valves, working electromagnetic valves and the sensor of temperature of ATF.

Executive electromagnetic valve of the distributing device and valvate assembly of the distributing device

Details of installation of the executive electromagnetic valve and valvate assembly of the distributing device

A — Valvate assembly of the distributing device
B — the Contact socket executive e/m the valve of the distributing device
With — the Executive electromagnetic valve of the distributing device

Efforts of a tightening of threaded connections, Nanometer

Т: 8


 PERFORMANCE ORDER

1. Tire out the car on the elevator.
2. Disconnect a negative wire from the battery.
3. Remove an air cleaner/airreception a chamber (see the Section Service of Components of an inlet air path of the Head of the Power supply system and release).
4. Remove the rocking limiter (see the Head Dvigatel).
5. Remove reception and central sections of system of production of the fulfilled gases (see the Head of the Power supply system and release).
6. Remove assembly of back section of system of production of the fulfilled gases with the muffler (see the Head of the Power supply system and release).
7. Lift the car and merge ATF, then screw a drain stopper and tighten it with the demanded effort.
8. Uncover the thermofilter.
9. Remove the driveshaft (see the Head Stsepleniye).
10. Prop up AT a special transmission jack, - track that persistent plates of transmission did not rest against the pallet.
11. Remove a back cross beam of transmission.
12. Remove back VSS (see the Section Removal and installation of the back sensor of the speed (VSS)).

13. Give a nut of a driving cable of the selector.

14. Shift a driving cable so that access to bolts of fastening of the case of lengthening of transmission opened.
15. Turn out fixing bolts and remove the lengthening case, - prepare in advance drain capacity for reception of the liquid containing in the case.
16. Disconnect an electrical wiring from the executive electromagnetic valve of the distributing device.
17. Remove the executive electromagnetic valve and the case of valvate assembly of the distributing device.
18. Installation is made upside-down. Track that all fixture was tightened with the demanded effort. After installation of the case of lengthening adjust a selector cable (see the Section Removal, installation, check of a state and adjustment of a driving cable of the AT selector). In summary add fresh ATF in transmission, having brought its level to the middle of a "cold" scale of the measuring probe.