Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
- Automatic transmission
   Specifications
   Electrohydraulic control system - the general information, purpose of basic elements
   System of self-diagnostics - the general information and the principles of functioning
   Diagnostics of the general condition of AT
   Problem diagnostics of AT
   Removal and installation of transmission assembly
   Replacement of elements of a suspension bracket of transmission assembly
   Replacement of an epiploon of a casing of lengthening of AT
   Check of a state, adjustment and replacement of the sensor switch of permission of start
   Removal and installation of the forward sensor of the speed (VSS)
   Removal and installation of the back sensor of the speed (VSS)
   Removal and installation of the sensor of turns of the turbine of the hydrotransformer
   Removal, service and installation of valvate assembly
   Replacement of electromagnetic valves of switching, executive electromagnetic valves and sensor of temperature of ATF
   Replacement of the ATF filter
   Removal and installation of the module of management of transmission (TCM)
   Removal, installation and check of a condition of lines of a path of cooling of ATF
   Removal, service and installation of components of the lever of the AT selector
   Removal, installation, check of a state and adjustment of a driving cable of the AT selector
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment









d9f1bda0


Removal, service and installation of components of the lever of the AT selector

AT selector lever design

1 — the Indicator lamp
2 — the Lock
3 — the Spring
4 — the Top section of the lever of the selector
5 — the Pin
6 — the Lower section of the lever of the selector
7 — the Finger
8 — the Plate
9 — the plug Through passage
10 — the Sealing element

11 — the lever Handle
12 — the Cover of the display panel
13 — the Pillow
14 — the Directing plate
15 — the Spring clamp
16 — the Cover of hummock assembly
17 — the Core of hummock assembly
18 — the Nut In
19 — the Nut And
20 — Clamps

REMOVAL

 PERFORMANCE ORDER

1. Tire out the car on the elevator.
2. Transfer the selector lever to the situation "N".
3. Lift the car.
4. Remove assembly of back section of system of production of the fulfilled gases with the muffler (see the Head of the Power supply system and release).
5. Uncover the thermofilter.

6. Disconnect a driving cable from the selector lever and remove a basic arm of a cable.

A Adjusting nuts
B Basic arm

7. Lower the car on the earth.
8. Remove assembly of the central console (see the Head Kuzov).
9. Separate contact sockets of an electrical wiring, turn out four fixing bolts and remove the selector lever from the car.

Dismantling and assembly

 PERFORMANCE ORDER

1. Remove the lever handle.
2. Remove a lamp of the indicator and a cover of the display panel.

3. Take two clamps and remove the directing plate.

And — Clamps
In — the Directing plate

4. Remove a cap and beat out a pin.

A — the Pin
B — the Lower section of the lever of the selector

5. Remove the lower section of the lever of the selector and separate the top section of the lever of the selector from a plate.
6. Carefully clear all components.
7. Assembly is made as it should be, the return to an order of dismantle of components. Grease all components with greasing like Nightight Lyw No. 2.
8. Having finished assembly, make sure of compliance of indications of the indicator to real position of the lever.
9. Estimate smoothness of movement of the top section of lever assembly.

INSTALLATION

 PERFORMANCE ORDER

Installation is made as it should be, the return to an order of dismantle of components. Track that all fixture was tightened with the demanded effort. Having finished installation, adjust a selector cable (see the Section Removal, installation, check of a state and adjustment of a driving cable of the AT selector) and make sure of serviceability of functioning of the lever of the selector.