Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
- Power supply system and release
   Specifications
   - System of injection of fuel
      Dropping pressure in a power supply system
      Depletion of a fuel tank
      Check of a state and replacement of fuel lines and their nipple connections
      Service of components of an inlet air path
      Removal and installation of the case of a throttle
      Service of components of the drive of a butterfly valve
      Removal, service and installation of the inlet pipeline
      Service of the fuel pump
      Removal and installation of the main MFI relay
      Removal and installation of the relay of the fuel pump
      Removal and installation of the sensor of a reserve of fuel
      Removal and installation of the fuel level sensor in an additional chamber of a fuel tank
      Removal, check and installation of the fuel filter
      Removal and installation of the locking valve of a cut-off of fuel
      Removal and installation of the damping fuel valves
      Removal and installation of a fuel tank
      Removal and installation of a jellied mouth of a fuel tank
      Removal and installation of components of system of injection of fuel
   + Control systems of the engine and decrease in toxicity of the fulfilled gases
   + System of production of the fulfilled gases
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment




d9f1bda0



Removal and installation of the case of a throttle

Details of installation of the case of a throttle of the 4-cylinder engine

1 — Sealing laying
2 — the Sensor of provision of a butterfly valve (TPS)
3 — the Electromagnetic valve of stabilization of turns of idling (IAC)
4 — the throttle Case

Efforts of a tightening of threaded connections, Nanometer

T1: 1.6
T2: 22


Details of installation of the case of a throttle of the 6-cylinder engine

1 — Sealing laying
2 — pressure Sensor in the inlet pipeline (MAP)
3 — the Electromagnetic IAC valve
4 — TPS
5 — the Sealing ring
6 — the throttle Case

Efforts of a tightening of threaded connections, Nanometer

T1: 1.6
T2: 2.8
T3: 22

L models 2.0 and 2.5

 PERFORMANCE ORDER

1. Details of installation of the case of a throttle of the 4-cylinder engine are shown on an illustration.
2. Disconnect a negative wire from the battery.
3. Remove assembly vozdukhoochistit la (see the Section Service of Components of an Inlet Air Path).


4. Disconnect cables of the drive of a butterfly valve (And) and (In).

And — a gas Cable
In — the Cable of a tempostat

5. Disconnect an electrical wiring from the electromagnetic valve of system of stabilization of turns of idling (IAC) and the sensor of provision of a butterfly valve (TPS).

And — TPS
In — the Electromagnetic IAC valve
With — Perepuskna an air hose

6. Disconnect perepuskny an air hose from the valve of admixture of secondary air to injectors.

7. Disconnect hoses of a cooling path from the throttle case.

8. Turn out bolts of fastening of the case of a throttle to the inlet pipeline.
9. Installation is made upside-down. Do not forget to replace all sealing elements. Bolts of fastening of the case of a throttle tighten 22 Nanometers with effort.

Models of 3.0 l

 PERFORMANCE ORDER

1. Details of installation of the case of a throttle are presented on an illustration.
2. Disconnect a negative wire from the battery.
3. Remove an airreception chamber (see the Section Service of Components of an Inlet Air Path).

4. Disconnect cables of the drive of a butterfly valve (And) and (In).

And — a gas Cable
In — the Cable of a tempostat

5. Disconnect an electrical wiring from the electromagnetic valve of system of stabilization of turns of idling (IAC) and the sensor of pressure in the inlet pipeline (MAP).

And — the MAP Sensor
In — the Electromagnetic IAC valve
With — Perepuskna an air hose

6. Disconnect from the IAC valve perepuskny an air hose.

7. Disconnect an electrical wiring from the sensor of provision of a butterfly valve (TPS).

8. Disconnect hoses of a cooling path from the throttle case.

9. Turn out bolts of fastening of the case of a throttle to the inlet pipeline.
10. Installation is made upside-down. Do not forget to replace all sealing elements. Bolts of fastening of the case of a throttle tighten 22 Nanometers with effort.