Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
- Power supply system and release
   Specifications
   - System of injection of fuel
      Dropping pressure in a power supply system
      Depletion of a fuel tank
      Check of a state and replacement of fuel lines and their nipple connections
      Service of components of an inlet air path
      Removal and installation of the case of a throttle
      Service of components of the drive of a butterfly valve
      Removal, service and installation of the inlet pipeline
      Service of the fuel pump
      Removal and installation of the main MFI relay
      Removal and installation of the relay of the fuel pump
      Removal and installation of the sensor of a reserve of fuel
      Removal and installation of the fuel level sensor in an additional chamber of a fuel tank
      Removal, check and installation of the fuel filter
      Removal and installation of the locking valve of a cut-off of fuel
      Removal and installation of the damping fuel valves
      Removal and installation of a fuel tank
      Removal and installation of a jellied mouth of a fuel tank
      Removal and installation of components of system of injection of fuel
   + Control systems of the engine and decrease in toxicity of the fulfilled gases
   + System of production of the fulfilled gases
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment









d9f1bda0


Removal and installation of a jellied mouth of a fuel tank

Design of a jellied mouth of a fuel tank

1 — the Main hose of a jellied mouth
2 — the Collar
3 — the Collar
4 — Sealing laying
5 — the Fixing flange
6 — the Cover

7 — the Protector

Efforts of a tightening of threaded connections, Nanometer

Т: 7.4

REMOVAL

 PERFORMANCE ORDER

1. Tire out the car on the elevator.
2. Dump pressure in a power supply system (see the Section Dropping Pressure in a power supply system).
3. Open the hatch of access and uncover a jellied mouth of a fuel tank.
4. Disconnect a negative wire from the battery.

5. Turn out fixing screws and remove a sealing flange.


6. Release nuts of fastening of the right back wheel, then lift the car over the earth and remove a wheel.
7. Merge fuel from the main chamber of a fuel tank (see the Head of the Power supply system and release).
8. Screw on a place and tighten a drain stopper with the demanded effort (26 Nanometers).
9. Install into place the panel of lateral protection of a tank and tighten bolts of its fastening with effort of 18 Nanometers.

10. Remove a protector of a jellied mouth.

11. Turn out bolts of arms of fastening of a vaporizing tube to a jellied mouth.

12. Turn out bolts of fastening of an arm of a jellied mouth to a body.


13. Release fixing collars and remove the main and ventilating hoses of a jellied mouth.
14. Remove a mouth.

INSTALLATION

 PERFORMANCE ORDER

1. Without closing the access hatch, establish a fuel plate (And) with a rubber sealant (C) and fill a jellied mouth in a reception opening from the inside of a wheel arch. Level a mouth, establish a cup (In) (see in the same place) and tighten fixing screws.

 At a bending of edges of a sealant inside straighten them by means of a screw-driver.

2. Put the main hose on the lower section of a tube of a jellied mouth (the overlap has to make about 35 ÷ 40 mm) and strongly fix it a collar.

 Track that collars did not concern a ventilating hose and a beam of a back suspension bracket!


3. Working in a similar manner, establish a hose a ventilating hose (the overlap when landing a hose to a tube has to make 25 ÷ 30 mm).
4. Tighten bolts of fastening of a basic arm of a jellied mouth to a body with effort of 7.4 Nanometers.
5. Tighten bolts of fastening of a vaporizing hose.
6. Further installation is made as it should be, the return to an order of dismantle of components. Track that elements of a jellied mouth did not adjoin to suspension bracket elements.