Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car


Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
- Cooling systems, heating
   Specifications
   + engine Cooling system
   - Systems of heating/ventilation/air conditioning
      Removal and installation of deflectors and air ducts
      Removal and installation of resistive assembly of a driving electric motor of the fan of a heater
      Removal, check and installation of a driving electric motor of the fan of a heater
      Removal and installation of the control panel functioning of systems of heating/ventilation/air conditioning
      Removal and installation of assembly of a heater
      Removal and installation of the heat exchanger of a heater
      Check of serviceability of functioning and service of systems of heating and air conditioning
      The K/V compressor - a design and the principle of functioning
      The K/V condenser - a design and the principle of functioning
      Receiver dehumidifier To/in - a design and the principle of functioning
      Pressure sensor switch To/in - a design and the principle of functioning
      The K/V evaporator - a design and the principle of functioning
      The K/V broad valve - a design and the principle of functioning
      Check of a state, removal and installation of the compressor of system To/in
      Removal and installation of the condenser of system To/in
      Removal and installation of a receiver dehumidifier of system To/in
      Removal and installation of the inlet block of system To/in, replacement of the evaporator
      Replacement of connecting hoses of a refrigerator path
      Check of serviceability of functioning of the sensor switch of pressure
      Removal and installation of information sensors of system of automatic central air (climate control)
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment



d9f1bda0

Removal and installation of the control panel functioning of systems of heating/ventilation/air conditioning

Details of installation of the control panel are shown by functioning of systems of heating/ventilation/air conditioning on illustrations.

Details of installation of the control panel functioning of systems of heating/ventilation/conditioning on hand-operated models To/in

1 — the Push-button switch
2 — the Handle of management
3 — the Control panel
4 — the Bearing module
5 — the Cover

6 — the Cable of the drive of the mixing gate
7 — the Switch of a choice of the high-speed mode of functioning of the fan
8 — the Printed-circuit board
9 — illumination Lamps


Details of installation of the control panel functioning of systems of heating/ventilation/conditioning on models with automatic To/in

1 — the Control panel
2 — the Printed-circuit board
3 — the Electronic control unit
4 — the Casing

5 — the Aspiratorny hose
6 — the air temperature Sensor in salon
7 — illumination Lamps


Hand-operated models To/in

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Remove forward section of finishing of the central console (And), then turn out 2 fixing screws (C) and remove the central section of finishing of the dashboard (D).
3. Turn the handle of a choice of temperature condition in extreme left situation (FULL HOT) and disconnect a cable of the drive of the mixing gate from a heater.

4. Release fixing screws and slightly release the control unit from console section of the dashboard.

5. Disconnect an antenna cable and remove assembly.
6. Installation is made upside-down, - track that the handle of a choice of temperature condition remained turned in extreme left situation (FULL HOT).


The models equipped with the automatic air conditioning system

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Remove forward section of finishing of the central console (And), then turn out 2 fixing screws (C) and remove the central section of finishing of the dashboard (D).

3. Release fixing screws and slightly release the control unit from console section of the dashboard.

4. Installation is made upside-down.