Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
- Coupling
   Specifications
   + Flywheel and coupling
   - Driving and cardan shaft, back differential
      The drive of forward wheels - the general information
      Removal and installation of rotary fists, service of stupichny assemblies of forward wheels
      Removal, service and installation of a forward power shaft
      The drive of back wheels - the general information
      Removal and installation of stupichny assemblies of back wheels, replacement of the back stupichny bearing
      Removal, check of a state and installation of components of the driveshaft
      Check of a state and replacement of a forward epiploon of back differential
      Removal, service, installation and adjustment of back differential of T-type
      Removal, service, installation and adjustment of back differential of VA type
      Removal, installation and check of a condition of a forward beam of fastening of back differential
      Removal, service and installation of a back power shaft
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment









d9f1bda0


Removal, check of a state and installation of components of the driveshaft

Details of installation of the driveshaft

1 — the Driveshaft
2 — Back differential
3 — the Plug

Efforts of a tightening of threaded connections, Nanometer

T1: 31
T2: 52

REMOVAL

 PERFORMANCE ORDER

 Before removal of the driveshaft wind metal parts with rags or rubber material since at removal these parts can damage rubber protection covers.

1. Disconnect a negative wire from the battery.
2. Install the AT selector lever in the situation "N"/include neutral transfer (RKPP)
3. Release the parking brake.
4. The car also establish to Poddomkratta it on props.
5. Remove central back (with the muffler) sections of system of production of the fulfilled gases, also uncover the thermofilter (see the Head of the Power supply system and release)

6. Mark position of the driveshaft of rather connecting back differential, then release four fixing bolts and turn out three of them.

7. Turn out two bolts of fastening of the central bearing to the car bottom.

8. Release the driveshaft from transmission, - try not to damage epiploons and the rubbing surface of the sliding collar.

 Prepare drain capacity for collecting oil which will flow out at removal of the driveshaft; right after extraction of a shaft muffle an opening in the case of lengthening of transmission by a special cover, or a polyethylene film.

CHECK

 PERFORMANCE ORDER

 The driveshaft is not subject to dismantling.


1. The key control geometrical parameters of the driveshaft are presented on an illustration.
2. Examine a surface of pipes of the driveshaft on existence of jags or cracks.
3. Estimate degree of wear of shlitsevy joints.
4. Check smoothness and noiselessness of operation of hinges.
5. Estimate the side play size, smoothness of the course and noiselessness of rotation of the central bearing.
6. Check a condition of epiploons.
7. By means of the dial measuring instrument determine the size of a beating of forward and back sections of a shaft in the central part of pipes. If the result of measurement exceeds 0.6 mm, replace a defective component.

INSTALLATION

 PERFORMANCE ORDER

1. Installation is made as it should be, the return to an order of dismantle of components. Track that all fixture was tightened with the demanded effort.
2. Manually turning a shaft, check it for existence of an excessive side play of gearing of shlitsevy connections, also estimate sizes of side plays in crosspieces and bearings of cardan hinges.
3. Rotating a hand back wheels, determine the size of an axial beating of the driveshaft.

 Perform measurements in the center of forward and back pipes of the driveshaft.

4. Pull a shaft in different directions around installation of the central bearing for the purpose of definition of a side play of the last.