Subaru Legacy/Outback

1999-2003 of release

Repair and operation of the car



Subaru of Legasi, Autbek
+ Cars Subaru Legacy, Outback
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling systems, heating
+ Power supply system and release
+ Electric equipment of the engine
+ Manual box and differential
+ Automatic transmission
+ Coupling
+ Brake system
- Suspension bracket and steering
   Specifications
   + Forward suspension bracket
   + Back suspension bracket
   - Steering
      Design and the principle of functioning of elements of the hydrostrengthened steering drive - the general information
      Adjustable safety steering column - the general information
      Removal and installation of a steering wheel
      Removal, check of a state and installation of the cardan hinge of a steering column
      Removal, service and installation of a steering column
      Removal, service and installation of the steering mechanism
      Removal, installation and check of a condition of elements of a hydraulic path of GUR
      Removal, service and installation of the steering pump
      Removal and installation of the tank of GUR liquid
      Check and replacement of GUR liquid, removal of air from a hydraulic path
   + Wheel assemblies, suspension bracket geometry
+ Body
+ Onboard electric equipment




d9f1bda0



Removal, service and installation of a steering column

 The description of procedures of removal/installation of assembly of the combined understeering switches is provided in the Head Onboard electric equipment.


Details of installation of a steering column

1 — the Safety steering column
2 — the Cardan hinge

Efforts of a tightening of threaded connections, Nanometer

T1: 24
T2: 25

REMOVAL

 PERFORMANCE ORDER

1. Tire out the car on the elevator.
2. Disconnect a negative wire from the battery.
3. Remove the module of a driver's safety cushion (see the Head Onboard electric equipment).
4. Remove a steering wheel (see the Section Removal and installation of a steering wheel).
5. Lift the car over the earth and remove the cardan hinge of a steering shaft (see the Section Removal, check of a state and installation of the cardan hinge of a steering column).
6. Lower the car and remove section of the lower finishing of the dashboard from the driver's party of salon.

7. Turn out the screw of fastening of the lower cover of a casing of a steering column.

8. Disunite contact sockets of all of the electrical wiring plaits brought to a steering column.

9. Turn out two fastenings of a steering column located under the bolt dashboard.

10. Release assembly of a steering shaft from a foot emphasis of a floor.

DISMANTLING

 PERFORMANCE ORDER

 The description of procedures of removal/installation of the combined understeering switches is provided in the Head Onboard electric equipment.

Turn out two screws of fastening of the top cover of a casing of a steering column, and also two screws of fastening of assembly of the combined understeering switches, and remove the corresponding components.

ASSEMBLY

 PERFORMANCE ORDER

1. Establish assembly of the combined switches on the top shaft of a column.
2. Establish the top cover, then pass plaits of an electrical wiring of understeering switches and the switch of ignition between basic to ledges of a cover and tighten fixing screws with the demanded effort (1.2 Nanometers).

CHECK

 PERFORMANCE ORDER

1. Carefully wipe external surfaces of components of assembly of a steering column pure rags and study their state. Replace defective details.

2. Measure the full length of assembly of a steering column. If the result of measurement exceeds the limit of admissible range (849.7 mm: for the Legacy models and 817.8 mm: for the Outback models), replace assembly.

INSTALLATION

 PERFORMANCE ORDER

1. Fill the plug through passage in the panel of a foot emphasis.

2. Pass the end of a steering shaft throughout the plug through passage.
3. Tighten the bolts of fastening of a steering column located under the dashboard with the demanded effort (25 Nanometers).
4. Restore initial connection of the electrical wiring plaits laid under the dashboard.
5. Connect the safety cushion electrical wiring socket on the cable reel, - track a zashchelkivaniye of the double lock.
6. Holding the lever of adjustment of an inclination of a column in the omitted situation, establish the lower cover of a casing of a steering column.
7. Connect the cardan hinge (see the Section Removal, check of a state and installation of the cardan hinge of a steering column).
8. Center provision of a contact drum of a chain of an electrical wiring of a horn/safety cushion (see the Head Onboard electric equipment), - track that forward wheels of the car were in rectilinear situation.
9. Establish and adjust a steering wheel (see the Section Removal and installation of a steering wheel) and the module of a driver's safety cushion (see the Head Onboard electric equipment).